Fri-Jado Cold MCC Скачать руководство пользователя страница 32

Страница: 32 / 147

Page 32

Rev 3 Service Manual MCC Hot / Cold 2021

5.3

MCC Cold Drop-in Requirements Self Serve

Important remark before installation:

When installing Front doors on the drop in unit, Please follow Front door installation

procedure, until step in which the glass is put in.

Placing the doors in a later stage, means the unit must be lifted again.

Installation must comply with:

•

No spark-forming components or components with a high surface temperature

(according to IEC 60079-15) may be present in the substructure/counter where the

counter is placed

•

The refrigeration components must not be directly accessible by unauthorized

personnel (according to IEC 60335-2-89)

•

Make sure that the counter is still easily accessible for service after installation by

means of a removable hatch.

The condenser must be cleaned regularly

•

Keep enough space on the back of the unit, to enable servicing which implies the

back panel of the counter can be removed

•

Provide enough space to place the counter with a stacker.

Maintain the dimensions and minimum height as indicated in the installation manual

(also applies to hot units)

•

Provide adequate ventilation; keep the minimum air inlet and outlet opening as

indicated in the installation manual.

Place baffles to prevent hot exhaust air from being sucked back through the

condenser

•

Make sure that the room/shop in which the furniture is placed meets the minimum

dimensions as indicated in the installation manual

•

All warning signs/labels, minimum floor area label (Cold unit) and data plate must remain

visible after installation

•

Operation of the appliance must be accessible.

•

Additional ventilation: prevent gas accumulation due to leakage.

•

Avoid high temperatures (> 200 ° C) in the vicinity of the furniture

Note:

Airflow inside the cabinet is crucial.

Air intake and Air outlet are not allowed to interfere.

A physical barrier

must be

placed in between the two air flows.

Air inlet and air outlet surfaces must comply with the specifications, (see previous page)

Содержание Cold MCC




















































































































































Результаты поиска

Содержание Cold MCC

Отзывы:

Бренды по названию

Популярные бренды

Fri-Jado Cold MCC, Руководство по обслуживанию

Результаты поиска

Содержание Cold MCC

Отзывы:

Бренды по названию

Популярные бренды