background image

Freedom Lite Marine Installation Manual Revision 3 

 

                        P a g e  

19 | 24

 

 

11.

 

Troubleshooting Guide  

 

Most issues with the Freedom LiTE can be resolved using the guide below.  If a problem 
cannot be resolved after referencing this table, please contact Freedom Won or your 
approved Freedom Won supplier.  

Table 11.1 Troubleshooting Guide (applicable to units with ON and OFF buttons)  

No.   Problem Description 

Cause / Solution 

The BMS (indicated by battery 
SoC display lighting up) does not 
stay on after the ON button is 
pressed 

1.

 

Error on the BMS. Check whether the red 
error light is illuminated on the SOC display 
when the ON button is held in. You can try 
to reset the error by pressing the RESET 
button for about 2 seconds and release. 
This should clear the error and allow the 
BMS to stay on after releasing the ON 
button. 

2.

 

Battery has been discharged to critically low 
level 

 remove all potential loads from the 

battery and switch off the inverter(s). Then 
try to switch on the BMS and then the 
breaker and get either a Solar Charger of AC 
Charger to charge as soon as possible 

 

ensure that the loads are switched off.  

3.

 

Battery has been charged to critically high 
voltage level 

 usually leaving the battery 

for an hour will allow the cell levels to drop 
down within acceptable levels and allow the 
BMS to be switched on again. Ensure that 
the suspect charge device is not able to 
charge the battery until you have 
established by it is overcharging 

 it could 

be that the CAN communication is not set 
up correctly or in the absence of CAN the 
relay control, or in the absence of relay 
control the charge voltage setpoint could be 
set too high.  

4.

 

If the BMS still does not switch on, please 
contact Freedom Won or your Authorised 
Distributor for further assistance. 

 

2

 

The Freedom LiTE has no voltage on 
the main output cables

 

Check that you have switched on the main breaker 
switch. Note 

 only turn this on once you are 

satisfied that you have completed the installation 
and that there are no DC or control wires that can 
short out or touch ground or other wires. Also 
ensure that you are ready to accept DC voltage onto 
the inverter before switching this breaker on. Also 
confirm that you have energised the BMS first by 

Содержание LiTE 10/8 Marine

























Отзывы: