FPG IN 5C08, Руководство по эксплуатации продукта

Страница: 31 / 52

IN 5C08/12/15/18/24.
- 31 - © Future Products Group
Refrigeration
cont.
REFRIGERATED CABINETS - SERVICING
FPG Settings Note that the following settings are Dixell factory defaults. Refer to the
Specification section for the correct FPG settings for your cabinet.
Dixell Default
Settings Label Name Range Default Setting
Set Set point LS÷ US -5.0
Hy Differential 0,1÷25.5°C/ 1÷ 255°F 2.0
LS Minimum set point -50°C÷SET/-58°F÷SET -50.0
US Maximum set point SET÷110°C/ SET ÷ 230°F 110
Ot Thermostat probe calibration -12÷12°C /-120÷120°F 0.0
P2P Evaporator probe presence n=not present; Y=pres. Y
OE Evaporator probe calibration -12÷12°C /-120÷120°F 0.0
P3P Third probe presence n=not present; Y=pres. n
O3 Third probe calibration -12÷12°C /-120÷120°F 0
P4P Fourth probe presence n=not present; Y=pres. n
O4 Fourth probe calibration -12÷12°C /-120÷120°F 0
OdS Outputs delay at start up 0÷255 min 0
AC Anti-short cycle delay 0 ÷ 50 min 1
rtr P1-P2 percentage for regulation 0 ÷ 100 (100=P1 , 0=P2) 100
CCt Continuous cycle duration 0.0÷24.0h 0.0
CCS Set point for continuous cycle (-55.0÷150,0°C) (-67÷302°F) -5
COn Compressor ON time with faulty probe 0 ÷ 255 min 15
COF Compressor OFF time with faulty probe 0 ÷ 255 min 30
CF Temperature measurement unit °C ÷ °F °C
rES Resolution in=integer; dE= dec.point dE
Lod Probe displayed P1;P2 P1
rEd2 X-REP display P1 - P2 - P3 - P4 - SEt - dtr P1
dLy Display temperature delay 0 ÷ 20.0 min (10 sec.) 0
dtr P1-P2 percentage for display 1 ÷ 99 50
tdF Defrost type EL=el. heater; in= hot gas EL
dFP Probe selection for defrost termination nP; P1; P2; P3; P4 P2
dtE Defrost termination temperature -50 ÷ 50 °C 8
IdF Interval between defrost cycles 1 ÷ 120 ore 6
MdF (Maximum) length for defrost 0 ÷ 255 min 30
dSd Start defrost delay 0÷99min 0
dFd Displaying during defrost rt, it, SEt, DEF it
dAd MAX display delay after defrost 0 ÷ 255 min 30
Fdt Draining time 0÷120 min 0
dPo First defrost after start-up n=after IdF; y=immed. n
dAF Defrost delay after fast freezing 0 ÷ 23h e 50’ 0.0
ALc Temperature alarms configuration rE= related to set; Ab = absolute Ab
ALU MAXIMUM temperature alarm Set÷110.0°C; Set÷230°F 110
ALL Minimum temperature alarm -50.0°C÷Set/ -58°F÷Set -50.0
Continued on next page