FP FPi2000 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 26

FP FPi2000 Скачать руководство пользователя страница 25

25

ENGLIS

H

8.

MAINTENANCE

8.1

Servicing

Disconnect the mains supply before
performing any maintenance.

The user must not attempt to service
the appliance beyond that described in
this operator manual. All other
servicing must be carried out by
qualified service personnel only.
Please contact your authorized
distributor.

8.2

General cleaning

The system must be kept in proper condition by
regularly removing dust, paper remains, etc.
Clean the sealing table and rubber rollers when
dirty. This can be done by using a slightly wetted
cloth soaked in warm water.

Do not clean the display with water or a cleaning
liquid.

8.3

Cleaning the brushes

Clean the brushes when dirty or saturated with
glue. An extra set of brushes is provided. The
best procedure is to always soak one set of
brushes and use the other set. In that way there
is always a clean set of brushes ready for
usage.
The brushes can be removed one by one by
pulling them straight off the brush holder. When
replacing the brushes, align the studs on each
brush with the respective holes in the brush
holder.
The brushes should be cleaned once a week.

8.4

Cleaning the moistening felt

Clean the moistening felt and water tray when
dirty or saturated with glue.

8.5

Cleaning the sensors

When the display shows a message like “Track
sensor dusty”, the sensors on the envelope or
document path must be cleaned. The screen on
the display indicates which sensor(s) must be
cleaned.

The sensors can be cleaned by using the bellow
located behind the side cover.
For cleaning the envelope track sensor, put the
bellow in the hole (refer to the section
"Operating controls"). Squeeze a few times
firmly to blow away the dust from the sensor.
Repeat this procedure for the other hole for
cleaning the flap sensor.

9.

OPTIONS

Optical Mark Reading

The system can be equipped with optical mark
reading. With this reading the system reads
optical marks that have been specially printed
on the documents. This code contains
information about the processing of the
documents.

Side exit

At the rear exit a side exit can be fitted by the
service organization. The side exit can be fitted
instead of the standard envelope receiving tray.
The side exit allows a conveyor, conveyor/
stacker or a franking machine to be fitted in line
with the machine.
When a side exit is ordered, a receiving tray will
be delivered with it. The side exit can be
mounted for exiting enveloppes to the left or to
the right.

10. SPECIFICATIONS

This operator manual refers to machines as
from machine number 04 DO-5001 or higher.

«
...
23
24
25
26
»

Содержание FPi2000



























Отзывы:

Нет отзывов