manualshive.com logo in svg

Fostex D-1624, Справочное руководство

Fostex D-1624 - качественный цифровой многодорожечный рекордер с продвинутыми функциями. Найдите подробное описание в Руководстве по эксплуатации, доступном для загрузки бесплатно на manualshive.com. Идеальный инструмент для профессионалов и любителей музыки.

Поделиться
Скачать
background image

D824/D1624 Reference Manual (MIDI Sync Function) 

83

5. Set slave type to “Vari” by the SETUP mode “Slave type setting.”

Refer to page “

112

”, SETUP mode “Slave type setting” for operating procedure and details.

6. Press the DISP SEL key while holding down the SHIFT key, to change the time base display to MTC.

<Precautions at MTC related setups>

The position (ABS 0 or 001BAR/1BEAT/00CLK) when the setup MTC (MTC offset time) should be output was
setup by the “MTC offset time setting” and “MTC offset mode setting.”  In accordance to start time of the tune set
by the sequence software, setup as explained below.

Offset mode: For ABS

Set the MTC offset time about three seconds prior to the start time of the tune set by the sequence software.
Because the recorder cannot immediately chase lock after input of MTC, in order to sync the unit from head of
the tune, set the preroll using the sequence software, and playback from before the actual head of the tune to
allow the recorder to enter into sync by the time it arrives at the head of the tune.

Offset mode: For BAR/BEAT

The MTC offset time can be set to the same time as the start time of the tune set by the sequence software.
Because the “ABS 0” position is set at the “0002BAR/1BEAT/00CLK” position in the unit, as mentioned before,
the preceding time required for sync is already set.  The preceding time of two bar lengths could change in
length depending on the first bar’s “signature setting” and “tempo setting” mentioned before.  For example, it
will be longer if the tempo is slowed down.

Confirming chase lock

1. When the sequence software is played, MTC IN LED of the recorder will light, “CHASE” in the display

will

change from blinking to lit and the chase lock will be completed.

Check that the MTC output by the sequence software and MTC time displayed in the recorder are the same.

2. When the sequence software stops, MTC will be interrupted and the recorder will also stop.

“CHASE” in the display will change from lit to blinking.

3. During FF/REW of the sequence software, the recorder will remain stopped but upon starting to record,

the recorder will immediately chase lock.

<Note>

Chase lock of the recorder by MTC only is permissible when speed difference of the MTC from the master is within
+/- 5.6%.  Against the MTC within this range, variable pitch will be constantly applied internally for chasing.
Chase lock, however, will not function against MTC at a speed difference outside this range.  Also, when the master
speed difference is large, it is advised to let the recorder learn the master speed by entering PLAY prior to recording.
By doing so, it will be lock faster from the second and later sessions.

* Should it not be possible to chase lock, re-check connections / cables and all settings.

Execution of recording

Carry out various recordings while the recorder is chase locked to the sequence software.

<One Point Advice>

Sync signal “Free” of the “Slave mode setting” menu:
When the recorder is made to chase lock by MTC only, variable pitch will be constantly applied by external MTC.
If a digital signal is output to an external digital equipment from the recorder, it will not be able to follow the
speed difference (MTC speed difference of the master) of the recorder and the external digital equipment, in
some cases, may not be able to input a continuous digital signal.
As a counter measure, the sync signal should be set to “Free” by the “Slave mode setting” menu.  Using this
setting, the recorder will enter self operation by the internal clock, after completion of chase lock, and it will be
possible to supply a stable digital signal to the external equipment.
Under this setting, when MTC drift between the master recorder and slave recorder exceeds 10 frames, the
recorder will assume that chase lock has been disengaged and the slave recorder will carry out position matching
again with the master unit (re-chase operation).  During the re-chase operation, sound output will be muted and
the digital signal will also be interrupted.  If it is within 10 frames, the slave recorder will continue to run while
admitting this drift.

Содержание D-1624









































































































































Отзывы:

Нет отзывов

Похожие инструкции для D-1624

Panasonic POVCAM AG-MDR25E Basic Operating Instructions Manual preview
POVCAM AG-MDR25E
Бренд: Panasonic Страницы: 64
Panasonic AJ-HPD2500 Operating Instructions Manual preview
AJ-HPD2500
Бренд: Panasonic Страницы: 226
Tascam DR-07mk II Owner'S Manual preview
DR-07mk II
Бренд: Tascam Страницы: 124
Olympus WS-650S Instructions Manual preview
WS-650S
Бренд: Olympus Страницы: 92
Paso DAG9300 Instruction Manual preview
DAG9300
Бренд: Paso Страницы: 12
Olin DVR-250 User Manual preview
DVR-250
Бренд: Olin Страницы: 27
Tascam DR-100 MKIII Service Manual preview
DR-100 MKIII
Бренд: Tascam Страницы: 43
Monacor DMR-425 Instruction Manual preview
DMR-425
Бренд: Monacor Страницы: 42
PENTRON AR-62 Manual preview
AR-62
Бренд: PENTRON Страницы: 13
Reach Bee9 User Manual preview
Bee9
Бренд: Reach Страницы: 20
Memorex MB2054 Operating Instructions Manual preview
MB2054
Бренд: Memorex Страницы: 15
LiteOn LVW-5001 User Manual preview
LVW-5001
Бренд: LiteOn Страницы: 35
LiteOn LVW-5005X User Manual preview
LVW-5005X
Бренд: LiteOn Страницы: 35
LiteOn DD-A100 Series User Manual preview
DD-A100 Series
Бренд: LiteOn Страницы: 56
LiteOn DD-500G User Manual preview
DD-500G
Бренд: LiteOn Страницы: 56
LiteOn HD-A940 Series User Manual preview
HD-A940 Series
Бренд: LiteOn Страницы: 84
LiteOn LVW-5045 User Manual preview
LVW-5045
Бренд: LiteOn Страницы: 104
Hyundai DVR 400 User Manual preview
DVR 400
Бренд: Hyundai Страницы: 128

Бренды по названию

Популярные бренды

Загрузить еще бренды