D824/D1624 Reference Manual (Names and Functions)
15
29. Record button [RECORD]
Pressing only this button places the readied tracks
into input monitoring status. Pressing this button
again will reset the tracks to playback monitoring.
(The RECORD LED will blink when the readied tracks
are in input monitoring status.)
Pressing the PLAY button while holding down this
button will place the readied tracks into recording.
At this time, the PLAY LED and RECORD LED will
light, and the readied track indication will be light
steadily (instead of blinking).
* Refer to page “
27
” of the “Before Starting” section for
more information about input monitoring and
reproduce monitoring.
* Refer to page “
23
” of the “Before Starting” section
for more information about ABS 0 and ABS END.
* Refer to page “
43
” for more information about Punch
In/Out recording using the foot switch.
* Refer to page "
67
" on details for "Clip board play."
* Refer to page "
57
" on details for "LOCATE 0" and
"LOCATE REC END."
28. Edit key [EDIT]
Pressing this key enters the recorder to the menu
select mode for editing tracks. Press this key
repeatedly or turn the JOG dial to select menu.
Edit menus appear in the following order. To execute
a desired menu, select the menu, then press the
EXECUTE/YES key. To exit the selection mode, press
the EXIT/NO key.
If the optional Model 8345 TC/SYNC card is installed,
you can enter the TC READY mode for recording
time code by pressing this key while pressing on the
SHIFT key.
* Refer to page “
66
” for more information about “Copy
Clip,” “Move Clip,” “Copy Paste,” “Erase,” and “Track
Exchange.”
* Refer to page “
35
” for more information about
program duplicate function.
<Note>
* This key is enabled only when the recorder is stopped.
30. Auto Punch Mode On/Off key [AUTO
PUNCH]
Switch this key ON for auto punch in/out.
When you press this key while a correct value is
stored to the AUTO PUNCH IN key and the AUTO
PUNCH OUT key, both the REHEARSAL LED and TAKE
LED will blink, indicating that Auto Punch mode is
on. (If a correct value is not stored, pressing the
AUTO PUNCH key will not turn the parameter ON,
and the message “Void Out Point!” will appear.)
Pressing the PLAY button under this condition will
put the recorder into “Rehearsal mode” for Auto
Punch In/Out recording. Pressing the PLAY button
and RECORD button simultaneously will put the
recorder into “Take mode.”
There are five combinations of the REHEARSAL LED
and TAKE LED that indicate the status of the recorder
regarding auto punch recording:
*1 Clipboard playback:
The recorder plays back the copy data or move data for
the Clipboard. During audio playback of the copy or move
data, the FL will display the time length and data type
(“Copy Clip Play!” or “Move Clip Play!”), and the copy or
move source track indicator will flash, enabling you to
quickly determine the track and data type.
*2 Locate ABS 0:
The recorder will locate the top of the selected Program
(ABS TIME: 00m: 00s: 00f).
*3 Locate REC END:
The recorder will locate the end of the recorded data on
the Program (ABS REC END).
These operations can be executed only on real tracks.
Auto Punch mode OFF
Both REHEARSAL LED and TALE LED are off.
Auto Punch mode ON
Both REHEARSAL LED and TALE LED are blinking.
Auto Punch TAKE mode
Only the TAKE LED (red) is lit.
Auto Punch REHEARSAL mode
Only the REHEARSAL LED (green) is lit.
Rehearsal mode entered by means of MMC or foot switch
Only the REHEARSAL LED (green) is blinking.
Copy Clip?
Move Clip?
Copy Paste? (Move Paste?(*1))
Erase?
Track Exchange?
PGM Duplicate?(*2)
(*1): After you execute copy clip, “Copy Paste”
appears. After you execute move clip, “Move
Paste” appears.
(*2): The program duplicate display will appear only
if the current drive was set to ON for the
"Multiple Undo Function" when formatting.
If the current drive is set to OFF, the program
duplicate display will not appear even if the
EDIT key is pressed.
Содержание D-1624
Страница 136: ...Memo...
