manualshive.com logo in svg

Forpark Australia Backhoe, Руководство по установке

Поделиться
Скачать
Forpark Australia Backhoe Скачать руководство пользователя страница 7

 

 

   

 

 

 

6 

FORPARK AUSTRALIA | www.forparkaust.com.au 

INSTALLATION MANUAL – FREE STANDING STATIC 23 
November 2017

 

BALL TOSS 

Attach the ball toss basket to the top of the upright using 17mm tri-lobe 
bolts and T-nuts (with the tri-lobe entering from inside the basket.  Dig a 
hole approximately 900mm deep and 500mm square.  Insert the upright 
making sure it is level.  Pour concrete around the base of the pole forming 
a footing of 500mm x 500mm x 600mm (deep), the top being 300mm 
below the finished surface level with a tapered top so that water won’t 
pool around the upright. (The footing extends 100m below the base of the 
upright so either the first 100mm of the footing should be allowed to set 
first or the pole should be rested on a brick or block before pouring the 
footing.)   Ensure that the upright is vertical after the concrete is poured.  
(Note:  Ensure the equipment is not used for at least 24 hours to allow the 
concrete to set.) 

 

 

BRONCO RIDER 

Dig holes for the four uprights spaced at a length of 
approximately 2350mm and width of 1350 (when 
measured from the centre of the holes).   

The holes should be approximately 800mm deep 
and 500mm square.  Insert the uprights making 
sure they are level with the top standing 1.0m above 
the finished surface level.  

 Pour concrete around the base of the poles 
forming a footing of 500mm x 500mm x 500mm, the top being 
300mm below the finished surface level with a tapered top so 
that water won’t pool around the upright.   

Check levels again after the concrete is poured.  Leave the 
concrete to set for at least 24 hours before attaching the 
remainder of the Bronco Rider.   

Place the frames on top of the beam, place the seats on top of 
the frames and fasten using 40mm cup head bolts and 
aluminium cap nuts.  Connect the support rails to the beam and uprights using ‘S’ hooks, ensuring that the ‘S’ 
hooks are fully closed using vice-grips. 

Содержание Backhoe




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды