manualshive.com logo in svg

formlabs Fuse 1, Руководство пользователя

Поделиться
Скачать
formlabs Fuse 1 Скачать руководство пользователя страница 27

Preparation and setup  | 

25

4.  Adjust the feet until the touchscreen indicates the printer is level.

4.6 

Setting up a network connection

For detailed guidance and visual assistance, visit 

support.formlabs.com

.

Connect the Fuse 1 to a secure network via Wi-Fi or Ethernet, providing it internet access for 
remote printing, remote troubleshooting, sending diagnostic logs, and receiving firmware 
updates. The Fuse 1 can connect directly to a computer with a USB cable.
For remote printing and monitoring, the Fuse 1 supports both wired (Ethernet) and wireless (Wi-
Fi) connections. Connect PreForm print preparation software to the same local-area network 
(LAN) as the printer in order to send a print job.
For a Windows operating system, after installing PreForm, check to ensure that Bonjour is 
properly installed. Bonjour is third-party software that is required to connect over Wi-Fi or 
Ethernet. Visit support.apple.com for assistance with Bonjour. The USB connection can still 
be used while the Fuse 1 is connected to a LAN.
When the Fuse 1 is connected to a LAN, its current status and print progress can be monitored 
with Dashboard: 

formlabs.com/dashboard.

4.6.1 

Connecting with Wi-Fi

The Fuse 1’s built-in Wi-Fi (IEEE 802.11 b/g/n) supports WPA/WPA2 security. Use the touchscreen 
to configure a wireless network connection.

To connect with Wi-Fi:

1.  Tap the wrench icon on the 

Home

 screen. The 

Settings

 screen appears.

2.  Tap 

Connectivity > Wi-F

i. The 

Wi-Fi

 screen appears.

3.  Toggle 

Use Wi-Fi

 to 

ON.

 The toggle turns blue.

4.  Tap the desired wireless network.
5.  If prompted, enter your network password and tap the checkmark to confirm.

4.6.2 

Connecting with Ethernet

The rear of the unit is equipped with a RJ-45 Ethernet (10BASE-T/100BASE-TX/1000BASE-T) 
1000 Mbit LAN Port. Use a shielded Ethernet cable (not included): minimum Cat5, or Cat5e 
or Cat6 for 1000BASE-T.

To connect with Ethernet:

1.  Plug one end of the Ethernet cable into the Ethernet port on the back of the unit.
2.  Connect the other end of the Ethernet cable to your LAN.

4.6.3 

Connecting with a manual IP configuration

When connected to an active Ethernet connection or available wireless network, the Fuse 
1 can be configured with a static IP address. Use the touchscreen to configure a manual 
IP connection.

To connect with Wi-Fi or Ethernet using a manual IP configuration:

1.  With an established Ethernet or available Wi-Fi connection, tap the wrench icon on the 

Home

 screen. The 

Settings

 screen appears.

2.  Tap 

Connectivity

. The 

Connectivity

 screen appears.

 °

For Wi-Fi networks, tap 

Wi-Fi

, then the desired wireless network. A new screen appears. 

Tap the 

Manual IP

 button in the lower-left corner. The 

Manual

 

IP

 

Settings

 screen appears.

 °

For Ethernet connections, tap 

Ethernet

. The 

Manual

 

IP

 

Settings

 screen appears.

3.  Toggle 

Use Manual IP 

to

 ON

. The toggle turns blue.

4.  Enter the appropriate 

IP Address, Subnet Mask, Default Gateway, 

and

 Name Server.

Содержание Fuse 1

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды