background image

58

Chapter 3 Advanced Operation

7.  Adjusting Spring Pressure

When feeding thick paper or slippery paper, the paper may stop at the conveyance roller without reaching to 

the folding roller. In this case, increase the spring pressure for the conveyance roller.

On the other hand, when feeding thin paper or flimsy paper, the paper may get wrinkled lengthways. In this 

case, decrease the spring pressure for the conveyance roller.

• 

When adjusting the spring pressure, turn off the machine.

• 

When adjusting the spring pressure, be careful not to harm your hand.

There are two springs on the operator’s side and 

the non-operator’s side. The standard position is as 

shown in the figure.

The position of the spring must be the same 

on the operator’s side and non-operator’s 

side. Otherwise, folding misalignment may 

occur.

Adjust the spring pressure in the following 

procedures.

[a]

[b]

Adjust the spring pressure by changing 

the position of the spring located 

inside.

The closer the hooked position is to the paper 

feed section [a], the higher the pressure is.
The closer the hooked position [b] to the 

ejecting section, the lower the pressure is.

To further increase the srping pressure, 

hook the spring closer to the paper feed 

section.

• 

If the spring pressure is too high, paper 

may get wrinkled.

•  If the spring pressure is too low, paper may 

not be conveyed.

After paper feed is finished or before feeding 

other paper, return each spring to the 

standard position.

Содержание FD 3300





































































































Отзывы: