Ford VSS Скачать руководство пользователя страница 71

Страница: 71 / 89

alarm should sound, indicating perimeter breach. Turn the alarm off by Turning the ignition to
"On".

• If equipped with OE perimeter security, there will be a 12 second interior chime prior to alarm

sounding. For vehicles not equipped with OE perimeter security, the alarm will trigger instantly
upon door opening.

• For push button start vehicles, the Intelligent Access (IA) key must be away from the vehicle,

otherwise the security system will disarm immediately upon trigger.

22. Exit the vehicle and arm it again, this time leaving the driver's door open. The vehicle should arm

itself, ignoring the open door but monitoring the rest. Once the vehicle is armed, shut the driver's
door and reopen it after a few seconds. The alarm should sound. Turn the alarm off by hitting
unlock on the keyfob.

• For push button start vehicles, the Intelligent Access (IA) key must be away from the vehicle,

otherwise the security system will disarm immediately upon trigger.

23. Test all other vehicle doors and the trunk in the same manner, by setting off the alarm and

disarming with the keyfob.

INSTALLATION (Continued)

21. Reach inside the window hit the door unlock trim switch. The LED should continue to flash,

indicating that the vehicle is still armed. Use the inside driver's door handle to open the door. The

201

Focus

Vehicle Security

Page 6 of 6

SK9L2J-19G364-AA

Содержание VSS


























































































Результаты поиска

Содержание VSS

Отзывы:

Похожие инструкции для VSS

Бренды по названию

Популярные бренды

Ford VSS, Руководство пользователя

Результаты поиска

Содержание VSS

Отзывы:

Похожие инструкции для VSS

Бренды по названию

Популярные бренды