Ford VSS Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 89

background image

NOTE:

5HYLHZ

vehicle specific wiring diagram(s).

NOTE:

5HYLHZ

proper wire splicing techniques.

13. Connect the Black ground wire from the

VSS

module harness to the chassis ground point on

the drivers side.

• Chassis ground points are located near the drivers side sill plate.

14.

NOTE:

A DVOM connected to the correct wire will show 0V, then show 12V when the Ignition Switch is
in the RUN and START positions.
A logic probe will show ground on the correct wire, then show power when the Ignition Switch is in
the RUN and START positions.

Identify the Brown/Yellow ignition circuit wire at the ignition switch harness.

15. Connect the Pink wire from the control module harness to the Brown/Yellow ignition circuit wire at

the ignition switch harness.

16.

NOTE:

A DVOM connected to the correct wire will show 0V, then show 12V when the Ignition Switch is
in the START position.
A logic probe will show ground on the correct wire, then show power when the Ignition Switch is in
the START position.

Identify the Blue/White starter circuit wire at the ignition switch harness.

17. Cut the Blue/White starter circuit wire at the ignition switch harness.

18. Connect the Violet wire from the control module harness to the harness Blue/White starter circuit

wire coming from steering column harness.

19. Connect the Violet/Red wire from the control module harness to the Blue/White starter circuit wire

coming from ignition switch connector.

INSTALLATION (Continued)

201

3

Fiesta - Key Start

Vehicle Security

5

Page 5 of 9

SK9L2J-19G364-AA

© Copyright Ford 201

1

FoMoCo

«
...
40
41
42
43
44
...
»

Содержание VSS


























































































Отзывы:

Нет отзывов

Похожие инструкции для VSS

Бренд: RightClick Страницы: 8

AutoCommand 20095

Бренд: Directed Electronics Страницы: 57

Бренд: Pandora Страницы: 25

Бренд: Sunrise System Страницы: 15

Бренд: ITI Страницы: 6

Бренд: AUTHOR Alarm Страницы: 48

Бренд: AUTHOR Alarm Страницы: 44

Бренд: AUTHOR Alarm Страницы: 52

Бренд: Equity Страницы: 2

Бренд: Equity Страницы: 2

Бренд: Equity Страницы: 2

vesda LaserFOCUS VLF-500

Бренд: Xtralis Страницы: 61

Бренд: ADE Страницы: 112

car security system

Бренд: PYLE Audio Страницы: 10

Бренд: olympia electronics Страницы: 2

Бренд: ENFORCER Страницы: 2

Бренд: ENFORCER Страницы: 4

Бренд: ENFORCER Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды