Fondital ITACA CTFS 24 Скачать руководство пользователя страница 95

Страница: 95 / 100

________________________________________________________________________________

AST 14 C 255/00

Boiler shut-down, picture

flashes:

Communication failure

between main board

and supplementary

boards

The main board does not

find all supplementary

boards or finds more than

the ones actually connected

Check parameter P60

value. It must

correspond to the

number of

supplementary

board(s) used

Boiler shut-down, picture

flashes:

Hydraulic configuration

not allowed

The main board does not

recognise the probes for

correct operation

Check the P3 board

configuration

parameter.

Boiler shut-down, picture

flashes:

Configuration error

between ambient

probe, remote control

or supplementary zone

board

The main board does not

recognise the settings

matched with the zones

Check the system

configuration

parameter values (P60

and P61).

Boiler shut-down, picture

flashes:

Ambient probe 1 (SA1)

fault

Disconnected or short-

circuited probe

Reconnect or replace it

Boiler shut-down, picture

flashes:

Ambient probe 2 (SA2)

fault

Disconnected or short-

circuited probe

Reconnect or replace it

Boiler shut-down, picture

flashes:

Pressure transducer

fault

Faulty transducer

Replace it

Disconnected transducer

Connect it

Boiler shut-down, picture

flashes:

Communication failure

with the interface board

Disconnected

communication cable

RS485

Check connections

Interface board or mother

board fault

Replace faulty board

Содержание ITACA CTFS 24





































































































Результаты поиска

Содержание ITACA CTFS 24

Отзывы:

Похожие инструкции для ITACA CTFS 24

Бренды по названию

Популярные бренды

Fondital ITACA CTFS 24, Руководство пользователя

Результаты поиска

Содержание ITACA CTFS 24

Отзывы:

Похожие инструкции для ITACA CTFS 24

Бренды по названию

Популярные бренды