FMI (V)KC36N series Скачать руководство пользователя

Страница: 28 / 44

www.fmiproducts.com

116226-01N

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn

by hand, don't try to repair it, call a

qualified service technician. Force or

attempted repair may result in a fire or

explosion.

D. Do not use this appliance if any part

has been under water. Immediately

call a qualified service technician to

inspect the appliance and to replace

any part of the control system and

any gas control which has been under

water.

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information

above.

2.  Open lower louver panel.
3.  Turn off all electric power to fireplace.
4.  Push in gas control knob slightly and turn

clockwise

to OFF.

5. Wait five (5) minutes to clear out any

gas. Then smell for gas, including near

the floor. If you smell gas, STOP! Follow

“B” in the safety information above. If you

don't smell gas, go to the next step.

6. The pilot is located by the main burner and

should not require accessing for lighting.

7. Turn gas control knob counterclockwise

to PILOT (see Figure 44).

8. Push in gas control knob all the way and

hold. Immediately light pilot by repeatedly

pressing piezo spark ignitor until a flame

appears. Continue to hold for about one

(1) minute after pilot is lit. Release gas

control knob and it will pop back. Pilot

should remain lit. If it goes out, repeat

steps 5 through 8.
• If gas control knob does not pop up when

released, stop and immediately call your

service technician or gas supplier.

• If pilot will not stay lit after several

tries, turn the gas control knob to OFF

and call your service technician or gas

supplier.

9. Turn on all electric power to fireplace.
10. Turn gas control knob counterclockwise

to ON.

OPERATION

Continued

PILOT

Figure 44 - Control Valve

Piezo

Ignitor

Gas Control Knob Variable Control Knob

11. This valve is equipped with a HI/LO fea

ture. Set fireplace input as desired.

12. To leave pilot lit and shut off burners only,

turn control knob clockwise

to the

PILOT position or set selector switch in

the OFF position.

13. Close lower louver panel.

TO TURN OFF GAS

TO APPLIANCE

1. Open lower louver panel.
2. Set selector switch in the OFF position to

prevent draining battery.

3. Turn off all electrical power to appliance

if service is to be performed.

4. Push in gas control knob slightly and turn

clockwise

to OFF.

5. Close lower louver panel.

MANUAL LIGHTING

PROCEDURE

1. Remove glass door (see

Removing/Re-

placing Glass Door

, page 25).

2. Follow steps 1 through 8 under Lighting

Instructions.

3. Press gas control knob and light pilot with

match.

4. Keep gas control knob pressed in for 30 sec

onds after lighting pilot. After 30 seconds,

release gas control knob. Follow steps 9

through 12 under

Lighting Instructions

5. Replace glass door (see

Removing/Re-

placing Glass Door

, page 25).

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must

be purchased separately (see Accessories,

page 37). Follow instructions included with

remote control.

Содержание (V)KC36N series













































Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды

FMI (V)KC36N series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды