FMI (V)KC36N series Скачать руководство пользователя

Страница: 9 / 44

www.fmiproducts.com

116226-01N

VENTING INSTALLATION

NOTICE: Failure to follow these in-

structions will void the warranty.

NOTICE: Do not seal termination

cap to vent pipe. Cap must be

removable for vent inspection

and maintenance.

INSTALLATION PRECAUTIONS

• Wear gloves and safety glasses for protec

tion.

• Use extreme caution when using ladders

or when on roof tops.

• Be aware of electrical wiring locations in

walls and ceilings.

The following actions will void the warranty

on your venting system:
• Installation of any damaged venting com

ponent.

• Unauthorized modification of the venting

system (Do not cut or alter vent compo

nents).

• Installation of any component part not

manufactured or approved by FMI PROD

UCTS, LLC.

• Installation other than as instructed by

these instructions.

WARNING: This gas fireplace

and vent assembly must be

vented directly to the outside.

The venting system must NEVER

be attached to a chimney serv

ing a separate solid fuel burning

appliance. Each direct-vent gas

appliance must use a separate

vent system. Do not use com

mon vent systems.

WARNING: Vent pipe air

space clearances to combus

tibles are 1" on all sides except

on the horizontal sections,

which require 2" clearances

from the top of the pipe. Where

the termination cap penetrates

a combustible wall, 1" air space

clearance is required.

NOTICE: Read these instruc-

tions completely before attempt

ing installation.

These models are tested and approved for

use with FMI PRODUCTS, LLC (direct-vent)

pipe components and terminations.
The venting system must terminate on the out

side of the structure and can not be attached

to a chimney or flue system serving a separate

solid fuel or gas burning appliance. A direct-vent

appliance must have its own venting system.

DO NOT common vent this appliance.
These models are approved to be vented

either horizontally through an outside wall or

vertically through a roof or chase enclosure

using the following guidelines:

• When venting system terminates horizon

tally on an outside wall, you may install

a standoff if the termination cap is to be

installed directly on a combustible finish

such as vinyl, wood, stucco, etc.

• Never run the vent downward as this may

cause excessive temperatures which could

cause a fire.

• Vent pipe air space clearances to com

bustibles are 1" on all sides except on the

horizontal sections, which requires 2" clear

ance from the top of the pipe. Where the

termination cap penetrates a combustible

wall, 1" air space clearance is required.

• Snorkel terminations are required when

minimum clearance to grade cannot be

met (see Figure 16 on page 13).

• Have fireplace and selected vent compo

nents on hand to help determine the exact

measurements when elbowing or offsetting.

Always use wall firestops when penetrating

walls and firestops when penetrating ceil

ings or attic spaces.

• If using a venting configuration of only

horizontal venting with no vertical run, a

1/4" rise for every 12" of run toward the

termination is required.

• For installation of fireplace at elevations of

4000 feet or greater, pay special attention

to venting requirement recommendations.

WARNING: Read all instructions

completely and thoroughly before

attempting installation. Failure to

do so could result in serious injury,

property damage or loss of life.

Содержание (V)KC36N series













































Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды

FMI (V)KC36N series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды