FMI (V)KC36N series Скачать руководство пользователя

Страница: 26 / 44

www.fmiproducts.com

116226-01N

FIREPLACE INSTALLATION

Continued

Figure 42 - Placing Ember Material on

Burner

Ember Material

Plenum

Andiron

4. Remount new frame at hinge with five

new screws before closing door. This will

ensure seating of gasket.

5. Close glass door frame. Lock latches by

placing bar under tab on door and pushing

down and back on latch (see Figure 41).

6. Replace screen/rod assembly by revers

ing step 1.

7. Replace louvers by reversing procedure

under

Removing Louver Panels,

page 25,

for KC36 series.

8. Replace screen door assembly, see remov

ing screen door assembly, page 25 see

Figure 40, for (V)KCC36 series.

Cleaning Glass Door

See

Cleaning and Maintenance

on page 30.

INSTALLING LAVA ROCK AND

GLOWING EMBERS

It is very important to keep logs exactly as

installed. Do not modify logs. Only use log

set designed for this fireplace.

WARNING: Logs are unitized

and not attached to the burner.

Do not handle log assembly by

top logs. Always pick up by the

bottom.

Open louvers, remove screen, unlock door

latches and open glass door. See

Removing

Glass Door

, steps 1 and 2, page 25.

1. Pull ember material apart into pieces no

larger than a dime. Place these pieces

loosely and sparingly directly onto ex

posed front section of burner (see Figure

42). This will create the glowing ember

appearance as flame touches ember

material. Do not block air slots by using

too much ember material in one area.

Place small pieces of ember material up

to the pilot and cover all pilot ports. It is not

necessary to use all of the ember material

provided.

2. Pour lava rock onto plenum but not onto

flat burner. It is not necessary to use all

of the lava rock provided.

NOTICE: Do not put lava rock on

burner or under burner. Placing

lava rock on burner will cause

performance problems.

3. Close glass door, lock door latches, replace

screen and close louvers (see

Removing

Glass Door

, page 25 steps 5 through 7).

WARNING: The glass door

must be securely in place before

running this fireplace. Do not run

this fireplace if glass is missing

or broken.

Figure 41 - Removing/Replacing Glass

Door

Lock

Unlock

Glass Frame

Assembly

Screw

Hinge

Latch

Place embers all the

way up to the pilot

Содержание (V)KC36N series













































Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды

FMI (V)KC36N series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды