FMI (V)KC36N series Скачать руководство пользователя

Страница: 25 / 44

www.fmiproducts.com

116226-01N

FIREPLACE INSTALLATION

Continued

REMOVING/REPLACING GLASS

DOOR

Replacing Screen Door Assembly

(KCC36 Series)

Push magnetic door latch out to the open

position. Position screen door tabs with slot

openings in upper face frame. Swing door

screen assembly in towards the bottom face,

Press in on the bottom of door screen until

magnetic door latch is pushed in.

Removing Glass Door

If replacement of glass is necessary, entire

assembly, glass and frame, must be replaced.

If glass is broken, wear gloves and tape re

maining fragments onto frame.

1. Remove screen assembly by pushing rod

either left or right, then down and forward

to remove screen/rod assembly from

firebox. Set assembly aside.

2. Lift up on latches to unlock. There are two

on top of firebox and two below firebox

that hold glass door in place (see Figure

41, page 26).

3. While holding glass door to prevent it from

falling and causing injury, remove five

screws from hinge located on left side of

door frame assembly (see Figure 41).

Figure 39 - Removing Louver Panel

Louver

Panel

Spring

Latch

Removing Screen Door Assembly

(KCC36 Series)

Push screen door assembly in toward the bottom

left and right sides until the magnetic door latch

pops the screen door out. Hold the screen door

assembly at the bottom and swing the door up

to disengage the tabs on the top of the door from

inside the slots underneath the upper face.

Figure 40 - Removing/Replacing Screen

Door Assembly (KCC36 Series)

Magnetic Door Latches

(KCC36 Series)

Screen Door Tabs

(KCC36 Series)

Slots underneath

Upper Face

CAUTION: Do not operate

this fireplace with a broken glass

door panel or without the glass

door panel securely in place. For

replacement part information

see

Replacement Parts

, page 36.

CAUTION: Wear gloves and

safety glasses while handling or

removing broken glass. Do not

remove if glass is hot. Keep chil

dren and pets away from glass.

WARNING: If fireplace has

been running, turn off and un

plug fireplace. Let cool before

removing glass door or louvers.

Removing Louver Panels

Remove top and bottom louver panels by

simultaneously pulling both top end spring

latches towards center of appliance until

they are disengaged from locating holes

(see Figure 39). Repeat for bottom spring

latches and pull louvers outward. To install

or replace items removed, simply reverse

procedures above.

Содержание (V)KC36N series













































Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды

FMI (V)KC36N series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание (V)KC36N series

Отзывы:

Похожие инструкции для (V)KC36N series

Бренды по названию

Популярные бренды