background image

T+/T+PRO English Instruction Sheet 

Page  

 

Beeper 

When the Tester detects a voltage, the LEDs light to indicate the 
voltage level, the Tester vibrates, and a beeper sounds (the T+ 
PRO also shows the voltage on the display). The beeper tones are 
different depending on what is being measured: 

 

AC voltage - the beeper is a chirping tone 

 

DC voltage - the beeper is a steady tone 

 

Continuity - the beeper is a steady tone for resistances less 
than 20 k

Ω

 

Note 

If any voltage is present, the Tester automatically 
switches to voltage mode. 

To turn the beeper on or off, press 

Z

 for more than 3 seconds. 

Each time the beeper is activated or deactivated, the Tester emits 
3 short beeps. 

Batteries are required for this feature. 

Vibration Voltage Indication 

The Tester vibrates when voltages 40 V and higher are measured. 
Batteries are required for vibration to function. 

Automatic Operation 

The Tester automatically turns on when the probes are placed 
across a complete circuit. The Tester selects continuity, ac or dc 
voltage modes based on the resistance or voltage between the 
probes. The tester switches off immediately after the test probes 
are removed from the circuit under test or after 5 seconds if 

C

 is 

released when the probes are not attached to a test circuit. If the 
HOLD function is activated, this switches off after 1 minute if a 
voltage is not detected. 

HOLD 

Press 

H

 to freeze the display reading. Press again to release 

HOLD. HOLD does not interfere with the voltage LED function.  

1.800.868.7495

[email protected]

Fluke-Direct

.ca

Содержание T+

















Отзывы: