background image

T+/T+PRO English Instruction Sheet 

Page 15  

 

Maintenance 

W

Caution 

Do not use abrasives or solvents on the Tester. 

Clean the case with a damp cloth and mild detergent. 

Replacing the Batteries 

Perform a self test to determine the charge state of the batteries 
on T+ Testers. The self test will not work with dead batteries. On 
T+ PRO Testers, the low battery icon (

B

) on the LCD indicates 

that the batteries need to be replaced.  

XW

Warning 

To avoid possible electric shock or personal injury: 

 

Disconnect test leads from any electrical source 
before opening the battery compartment. 

 

Do not operate the Tester with the battery door or 
portions of the cover removed or loosened. 

 

1.

 

Turn the Tester over and use a flat-head screwdriver to 
loosen the battery door screw and remove the door. 

2.

 

Replace the batteries with two new AAA alkaline batteries. 

3.

 

Reattach the battery compartment door and reinstall the 
screw. 

Specifications 

Temperature: 

Operating: -10 

°

C to 55 

°

C (14 

°

F to 131 

°

F) 

Storage: -30 

°

C to +60 

°

C (-22 

°

F to +140 

°

F) 

Relative Humidity: 

°

C to 30 

°

C (32 

°

F to 86 

°

F) 90 % 

30 

°

C to 40 

°

C (86 

°

F to 104 

°

F) 75 % 

40 

°

C to 50 

°

C (104 

°

F to 122 

°

F): 45 % 

Altitude: 

Operating: 2,000 m 
Storage: 10,000 m 

Battery Type/Life:  AAA (2); 40 hours 
Shock, Vibration:  Sinusoidal vibration per MIL-PRF-28800F for a  

Class 2 instrument  

Safety: 

ANSI/ISA S82.02.01, CSA C22.2-1010.1, IEC 61010-1 
to 1000 V CAT III/600 V CAT IV; Pollution Degree II 

AC Bandwidth:

 

45 Hz to 66 Hz 

Maximum Input  
Voltage Between  
Terminal and  
Earth Ground:

 

Maximum working voltage 1000 V ac or dc. 
Maximum measurable voltage 600 V ac or dc. This will 
be displayed on the LED and the LCD (T+ PRO). 

Duty Cycle:

 

Indefinitely for voltages up to 240 V. 
For voltages between 240 V to 600 V the duty cycle is 
30 seconds on / 300 seconds off.  For voltages above 
240 V the Tester must connect to a voltage source 

1.800.868.7495

[email protected]

Fluke-Direct

.ca

Содержание T+

















Отзывы: