background image

T+/T+PRO English Instruction Sheet 

Page  

 

 

When using the probes, keep fingers away from 
the ends of the probe tips. 

 

Connect the common test lead before 
connecting the live test lead. When 
disconnecting the test leads, disconnect the live 
test lead first.  

 

Do not operate the Tester with the battery door 
or portions of the cover removed or loosened. 

 

When the batteries are depleted, self test will not 
function.  

 

When the beeper is disabled, it will not sound 
until the beeper is reactivated. 

 

For voltages above 240 V, you must only connect 
to a voltage source for a MAXIMUM of 30s and 
then disconnect for a MINIMUM of 300s. 

 

Perform a self test before any measurements are 
taken for voltage, continuity, resistance, or 
rotary field.  See “Self Test”. 

 

Exercise caution when performing 
measurements on PLC (Programmable Logical 
Controller) inputs. When measuring relay control 
voltages on PLCs, be aware that this may open 
or close the relay/switch. 

 

All appliances or equipment on the circuit being 
tested should be unplugged to help avoid 
erroneous readings. 

W

Caution

 

Although the Tester may be used with depleted batteries, 
replace depleted batteries immediately to avoid Tester 
damage from battery acid leakage. 

1.800.868.7495

[email protected]

Fluke-Direct

.ca

Содержание T+

















Отзывы: