Flow 94K HYPERPRESSURE Скачать руководство пользователя страница 20

Страница: 20 / 82

5. Connect the hand pump hose to the tool at the

quick-disconnect fitting (see below).

Note:

On some tool models the hand pump hose

does not have a quick-disconnect fitting. If this is the
case, leave the hose attached to the tool at all times
to prevent leaking.

6. Open the pressure-release valve on the hand pump

by turning the valve handle counter-clockwise one
turn.

7. Collapse the pressure loading tool using a ratchet

and socket on the tool nuts. In the pattern shown be-
low, torque the tool nuts to 20 ft-lb (27 N-m), then
to 50 ft-lb (67.8 N-m).

Note:

Oil from the tool will flow back to the hand

pump reservoir.

8. Close the hand pump pressure-release valve by turn-

ing the valve handle clockwise until tight.

9. Pump the tool to 9200 psi (634 bar).

Wait 10 seconds, then recheck the gauge. If the
needle falls off the mark, re-tighten the pump pres-
sure relief valve and bring the pressure back up to
the 9200 psi (634 bar) mark.

10. Run up the end cap nuts by hand. Using a torque

wrench with a crow’s foot end, torque in the pattern
indicated (see illustration below) to 50 ft-lb
(67.8 N-m).

Note

: The pressure reading will drop as the nuts are

torqued. This is normal; do not adjust pressure.

CAUTION

Do NOT repump the tool after starting the

end cap nut torquing. Repumping the tool

can cause misalignment and break parts.

11. Bleed off the remaining tool pressure by opening the

pump pressure-release valve.

12. Remove the hand pump hose from the tool at the

quick-disconnect fitting.

Note:

On some tool models the hand pump hose

does not have a quick-disconnect fitting. In this case,
the hose should be left attached to the tool at all
times to prevent leaking.

13. Remove the pressure loading tool nuts and washers.

Remove the tool.

20 | M-376

94K HYPERPRESSURE INTENSIFIER

Содержание 94K HYPERPRESSURE



















































































Результаты поиска

Содержание 94K HYPERPRESSURE

Отзывы:

Бренды по названию

Популярные бренды

Flow 94K HYPERPRESSURE, Руководство пользователя

Результаты поиска

Содержание 94K HYPERPRESSURE

Отзывы:

Бренды по названию

Популярные бренды