Flow 94K HYPERPRESSURE страница 28 Скачать руководство пользователя

Страница: 28 / 82

014623-1or -3 Long-block intensifier
(StoneCrafter)

020070-1 Short-block intensifier
(HyperPressure)

6. Remove the end cap from the tie rods. The check valve

assembly will remain inside the end cap due to com-
pression of the o-ring on the check valve body.

Note:

Unless check valve maintenance is necessary

(Maintenance Procedure D), you do not need to remove
the check valve assembly from the end cap.

7. Remove the high-pressure cylinder and filler tube from

the intensifier end bell. Rocking the cylinder gently
while pulling will help separate the cylinder from the
end bell.

CAUTION

When the cylinder is clear of the end bell, pull it

straight out to avoid contact with the ceramic plunger.

Otherwise, you could damage the plunger.

28 | M-376

94K HYPERPRESSURE INTENSIFIER

Содержание 94K HYPERPRESSURE



















































































Результаты поиска

Содержание 94K HYPERPRESSURE

Отзывы:

Похожие инструкции для 94K HYPERPRESSURE

Бренды по названию

Популярные бренды

Flow 94K HYPERPRESSURE, Руководство пользователя

Результаты поиска

Содержание 94K HYPERPRESSURE

Отзывы:

Похожие инструкции для 94K HYPERPRESSURE

Бренды по названию

Популярные бренды