Flow 94K HYPERPRESSURE страница 22 Скачать руководство пользователя

Страница: 22 / 82

10. Using the ratchet and socket, back off the tool nuts

exactly one

full turn.

CAUTION

Failure to properly back off the tool nuts will

make it impossible to remove the tool from the

tie rod, and could damage the intensifier.

11. Close the hand pump pressure-release valve by turn-

ing the valve handle clockwise until tight.

12. Pump the tool to the 9200 psi (634 bar) mark on the

pressure gauge.

Note:

It will take 60–70 pumps before pressure will

begin to build.

13. Wait 10 seconds, then recheck the gauge. If the nee-

dle falls off the mark, retighten the pump pressure
relief valve and bring pressure back up to the
9200 psi (634 bar) mark.

14. Loosen the four end cap nuts and back off

two

full

turns.

15. Bleed off the tool pressure by opening the pump

pressure-release valve.

16. Remove the hand pump hose from the tool at the

quick-disconnect fitting.

Note:

On some tool models the hand pump hose

does not have a quick-disconnect fitting. If this is the
case, leave the hose attached to the tool at all times
to prevent leaking.

17. Remove the pressure loading tool nuts and washers,

then remove the tool.

18. Remove the end cap nuts and washers.

22 | M-376

94K HYPERPRESSURE INTENSIFIER

Содержание 94K HYPERPRESSURE



















































































Результаты поиска

Содержание 94K HYPERPRESSURE

Отзывы:

Похожие инструкции для 94K HYPERPRESSURE

Бренды по названию

Популярные бренды

Flow 94K HYPERPRESSURE, Руководство пользователя

Результаты поиска

Содержание 94K HYPERPRESSURE

Отзывы:

Похожие инструкции для 94K HYPERPRESSURE

Бренды по названию

Популярные бренды