Fisher Scientific Isotemp 500 Series Скачать руководство пользователя страница 19

Страница: 19 / 24

Page 15

Isotemp Economy Incubators

Trouble-Shooting Table

This table is intended to assist in the resolving incubator problems by

relating symptoms to their likely causes. The service discussed below is
beyond the scope of most users and should be performed by qualified and
trained personnel.

Symptom Probable

Cause

Action

No power

Unit not plugged in or turned on.

Plug in or turn on.

Defective circuit breaker.

Replace circuit breaker.

Incubator temperature

Defective control thermocouple

Replace control thermocouple

erratically high

Failure to heat

Set temperature less than

Refer to

Operation Section

actual temperature

Defective control thermocouple

Replace control thermocouple

Poor

heater

connections

Tighten connections at terminal strip

Defective heater element

Check heater resistance on schematic
at back of manual. Replace heater
unless approximately same as
schematic.

Defective controller

Replace controller

Alarm LED stays on and Set temperature has been

Wait for actual temperature to cool to

control is higher than set changed to a value less than

the set temperature

temperature

the high alarm limit

Defective control thermocouple

Replace control thermocouple

Defective controller

Replace controller

Содержание Isotemp 500 Series

























Результаты поиска

Содержание Isotemp 500 Series

Отзывы:

Похожие инструкции для Isotemp 500 Series

Бренды по названию

Популярные бренды

Fisher Scientific Isotemp 500 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Isotemp 500 Series

Отзывы:

Похожие инструкции для Isotemp 500 Series

Бренды по названию

Популярные бренды