Fisher Scientific Isotemp 500 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

background image

Isotemp Economy Incubators

Page 4

Controls

The 500 Series controller features three LED’s which indicate,
respectively, that power is being applied to the incubator heaters, an
alarm condition exists or that incubator power is on. A temperature dial,
marked in five degree increments, serves to set the incubator temperature.

Temperature

Sets the incubator operating temperature in degrees

Dial

Celsius (

°

C).

Heat Indicator

Lights when power is being supplied to the incubator

heater.

Alarm Indicator

Lights if the actual incubator temperature exceeds the

alarm temperature. The alarm temperature is

factory-adjusted to be 3

°

C above the set temperature.

Power Indicator

Lights when the power is on.

«
...
6
7
8
9
10
...
»

Содержание Isotemp 500 Series

























Отзывы:

Нет отзывов

Похожие инструкции для Isotemp 500 Series

Бренд: LAUMAS Страницы: 40

Бренд: Campbell Страницы: 2

Бренд: DANA Страницы: 42

Бренд: Yakima Страницы: 8

CSL Elite Racing Wheel

Бренд: FANATEC Страницы: 2

Бренд: FANATEC Страницы: 8

Бренд: FANATEC Страницы: 35

Бренд: Vello Страницы: 12

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 6

Portrait Series

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 10

Бренд: daviteq Страницы: 33

6130N - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Varta Страницы: 132

BTL5-T1 M P-S103 Series

Бренд: Balluff Страницы: 20

Бренд: Powercore Страницы: 2

Бренд: TeleVue Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды