Fisher Scientific AccuSpin Micro 17 Скачать руководство пользователя страница 52

Страница: 52 / 79

Troubleshooting

Error

Symptom

Possible causes and corrective measures

E-22/E-23

Rotor stops without
deceleration to standstill.

Instrument cannot be
operated.

Error in speed entry

Switch the instrument off and on again.

If the error persists, contact service representative.

E-24

Instrument cannot be
operated.

Wrong status information from the lid-latch.

1. Turn the centrifuge off and on.

2. After re-switching on, the display shows "

Lid FAiL

3. If the centrifuge lid has been already opened, the display

shows "

Close Lid

". Thereupon close the lid.

4. The centrifuge tries to open the lid to switch for starting

the normal operation mode.
If the error persists, contact service representative.

E-29

Motor does not start.

Motor or rotor blocked.

1. Switch instrument off and on again using the mains

switch.

2. Open the centrifuge lid.
3. Check whether the rotor can turn freely.

If you cannot clear the malfunction, contact a service
representative.

Содержание AccuSpin Micro 17
















































































Результаты поиска

Содержание AccuSpin Micro 17

Отзывы:

Бренды по названию

Популярные бренды

Fisher Scientific AccuSpin Micro 17, Инструкция по эксплуатации

Результаты поиска

Содержание AccuSpin Micro 17

Отзывы:

Бренды по названию

Популярные бренды