Fisher Scientific AccuSpin Micro 17 Скачать руководство пользователя страница 13

Страница: 13 / 79

Before use

Before use

Where to install the centrifuge

The centrifuge may only be used indoors. Its location
must meet the following criteria:

•

A safety zone of 30 cm around the centrifuge must

be maintained. Hazardous materials must not be
kept within this zone during centrifugation.

•

The substructure must be stable and resonance-

free. A good support is provided by a plane labora-
tory bench or a large laboratory carriage with cast-
ers that may be locked.

•

In the area of 15 cm around the centrifuge a suffi-

cient air circulation has to be ensured.

•

The centrifuge must be protected from heat and

direct sunshine. The ultraviolet radiation may dam-
age the housing.

•

The installation site should be always well venti-

lated.

Transport and installation the centrifuge

Transport the centrifuge only in
the upright position, using the
special box provided with the in-
strument, and secure it properly.

Place the centrifuge carefully to
avoid damages.

Lift up the instrument only on the bottom
plate. Mind the weight of the centrifuge
during the transport!

(See „Technical data“)

Let someone assist you in carrying the
centrifuge!

Centrifuge with refrigeration unit

In order to allow the coolant to set-
tle down in the compressor, the
instrument must be left idle at the
new location for approx. 1 hour.

Содержание AccuSpin Micro 17
















































































Результаты поиска

Содержание AccuSpin Micro 17

Отзывы:

Бренды по названию

Популярные бренды

Fisher Scientific AccuSpin Micro 17, Инструкция по эксплуатации

Результаты поиска

Содержание AccuSpin Micro 17

Отзывы:

Бренды по названию

Популярные бренды