manualshive.com logo in svg

Fisher Scientific AccuSpin Micro 17, Инструкция по эксплуатации

Поделиться
Скачать
Fisher Scientific AccuSpin Micro 17 Скачать руководство пользователя страница 28

Operation 

24 

Installing the rotor 

 
 

Improper or improperly combined 

 

 

accessories may cause severe dam-
age to the centrifuge!

 

 

The centrifuge rotors

 

approved are detailed in the 

chapter “Accessories". Use only rotors listed for this 
instrument. 

To insert the rotor, you need the special wrench deliv-
ered with the instrument (see chapter "accessories”). 

 

You may insert the rotor only when the temperature 
difference of the drive and the rotor drive shaft 
achieves maximum 20 °C. Otherwise the rotor may jam 
during the installation. 

 

 

The installation of a clamping rotor 
can lead to demages of the drive 
shaft and rotor!  

 

 

Proceed as follows: 

1.  Open the centrifuge lid and make sure that the 

rotor chamber and the rotor are clean. Remove 
eventual dust, foreign material or sample residues. 
The thread and the O-Ring on the motor shaft must 
be in perfect condition. 

2.  Turn the rotor so that the notch for engaging the 

drive shaft points downward. 

3.  Place the rotor on top of the drive shaft so that the 

notch of the rotor is located precisely above the re-
taining pin. (There a two bars in the labelling on the 
upper side of the rotor indicating the position of the 
notch). These bars make the positioning easy. 

Содержание AccuSpin Micro 17
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды