manualshive.com logo in svg

Fisher Scientific AccuSpin Micro 17, Инструкция по эксплуатации

Поделиться
Скачать
Fisher Scientific AccuSpin Micro 17 Скачать руководство пользователя страница 45

Maintenance and care 

  41

Decontamination 

 

For general radioactive decontamination, use a solu-
tion of equal parts of 70% ethanol, 10% SDS and wa-
ter. Follow this with ethanol rinses, then de-ionized 
water rinses, and dry with a soft absorbent cloth. Dis-
pose of all washing solutions in appropriate radioactive 
waste containers! 

 

Autoclaving  

 

 Check whether autoclaving is permitted!

  

 
 

You may autoclave the rotor, rotor lid and the adapters 
at 121 °C. 

Maximum permissible autoclaving cycle: 

20 minutes at 121 °C. 

 

For safety reasons, the plastic 
rotors and rotor lids must only 
be subjected to a maximum of 20 
autoclaving cycles! 

The rotor must be cleaned and rinsed with distilled 
water before being autoclaved. Remove the rotor lid, 
the centrifuge tubes and the adapters. Place plastic 
rotors on an even surface to avoid deformation. 

 

Chemical additives to the steam are not 
permitted. 

 

 

Never exceed the maximum permis-
sible values for autoclaving tem-
perature and autoclaving time. 

Should the rotor show signs of wear 
or corrosion, you must stop using 
it! 

 

 

Содержание AccuSpin Micro 17
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды