manualshive.com logo in svg

Fisher & Paykel Titan Aerotech OD302EU, Руководство по обслуживанию

Поделиться
Скачать
Fisher & Paykel Titan Aerotech OD302EU Скачать руководство пользователя страница 50

Service Manual 546596A: 302 Series Titan Oven

June 2005

 50

7.

 

Service Procedures

In order to service components of the oven, certain procedures must be followed.  These
procedures are as follows:

ƒ

  To avoid stripping screws do not over tighten when reassembling parts.  If using a

screw gun have the torque setting on low.

ƒ

  Take extra care not to damage wire terminals on removal as some have release clips.

7.1

 

Removal from Joinery Cavity

1.  Disconnect the unit from the power supply.
2.  Remove the oven doors, shelves and utensils.  (refer to Section 7.21)
3.  Remove the two screws on either side of the oven frame that secure the oven to the

joinery.

4.  Slide the oven out of the cavity onto a suitable support.

Warning:  This oven is heavy and care should be taken to use correct lifting
techniques.
Reassembly

ƒ

  Refit in reverse manner

7.2

 

Components in Control Panel Area

1.  Remove the oven from the joinery cavity.  (refer to Section 7.1)

Warning:  

To avoid the oven tipping forward, remove the shelves, utensils and doors.

(refer to Section 7.21)

Note:

  The oven does not need to be removed completely from the joinery cavity.  Sliding

the oven out eight inches (200mm) will give sufficient access space.
2.  Detach the control panel from the frame uprights by removing the two screws located

either side of the rear of control panel.

3.  Remove the wiring harness from the power module.
4.  Lift the control panel off the two support brackets.

ƒ

  The function, temperature and clock modules are now accessible.

Reassembly

ƒ

  Refit in reverse manner.

Содержание Titan Aerotech OD302EU








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды