First 21128 Скачать руководство пользователя страница 18

ROTOTERM MR-TR

18

www.first.si

STATUS

POSSIBLE FAULT

REMEDY

LED  for  valve  closing  ( )  is  ON  on 

controller, mixing valve is opened, heating 

water line is hot

-  Motor  MV  120/…  rotation  direction  is 

inverted regarding mixing valve.

Check motor rotation direction left and 

right.

Temperature in the room is always the 

same regardless of program

Slide switch 1 is in position  

1 (

) or 

 

0 ( )

Set slide switch 1 to     position AUTO

Too cold in the room.

- Slide switch 5 in position

 

- Terminal  pins  9  and  10  on    room  unit  is 

inverted

- Knobs for temperature setting are set to 

low

- set selector switch 5 to  

  position  .

-  check  connection  of  room  unit 

AS2000-E

- set knobs (5 and 6) to higher level

At timer status “

 is cold in the room, 

at status “ “ is warmer.

- Terminal  pins  9  and  10  on    room  unit  is 

inverted

-  check  connection  of  room  unit 

AS2000-E

If T2 or T3 key is pressed, Er1 is 

displayed.

- Sensor T2 or T3 interrupted

- Sensors out of function

- Check T2 and T3 sensors.

If T2 or T3 key is pressed, Er2 is 

displayed.

- Sensor T2 or T3 short 

  circuited.

- Check T2 and T3 sensors.

The controller operating normally. 

Sometimes it happens that the controller 

repeatedly reset (off and on again).

In the system appears strong 

electromagnetic interference. Controller 

activates the built-in

protection against electromagnetic 

pulses.

Contact central service

After the completion of maintenance work on the heating system check:

 - el. connection of sensors, room unit, controller, actuator, pump

 - Check operation of pumps, mixing valve actuator

 - setting parameters on the room unit and the controller

 - position of slide switches on the room unit and the controller

YOUR’S PROGRAM

Write down your's program

switch 

cycle

1

2

3

4

5

6

7

8

temp. level

higher

lower

higher

lower

higher

lower

higher

lower

day

time

switch 

cycle

9

10

11

12

13

14

15

16

temp. level

higher

lower

higher

lower

higher

lower

higher

lower

day

time

FIRŠT ROTOTEHNIKA

Radegunda 54, 3330 Mozirje, Slovenia

PE VELENJE

Koroška cesta 56a, 3320 VELENJE, Slovenija

tel. +386 3 898 35 00, fax. +386 3 898 35 35

e-mail:[email protected], www.first.si

Содержание 21128



















Отзывы: