Firegear Kalea Bay OFP-60LECO-N Скачать руководство пользователя страница 26

Страница: 26 / 38

Kalea Bay Outdoor Fireplace

REV. 4-17-19 Page 26

CAUTION

: Children and adults should be alerted to the hazards on high surface temperatures and should stay away to

avoid burns or clothing ignition. Young children should be carefully supervised when they are in the area of the appliance.

WARNING:

Do not use this appliance if any part has been under water. Immediately call a qualified service technician

to inspect the appliance and to replace any part of control system and any gas control, that has been under water.

OPERATION

SAFETY WARNINGS

1. Never leave the fireplace unattended during operation.

2. Clothing or other flammable materials should not be placed on or near the appliance.

3. Any guard or other protective device removed for servicing the appliance must be replaced prior to operating the

appliance.

4. Installation and repair should be done by a qualified service person. The appliance should be inspected before

use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It

is imperative the control compartment, burners and circulating air passageways of the appliance be kept clean.

5. Inspect the fuel supply connection before each use of the appliance.

6. Temporary storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply

(Natural or L.P. gas line).

WARNING

1. This appliance is hot when operated and can cause severe burns if contacted.

2. Do not burn any solid fuels in this appliance.

LIGHTING INSTRUCTIONS

READ ALL WARNING AND SAFETY INFORMATION ABOVE BEFORE ATTEMPTING TO LIGHT FIREPLACE

Turn

main gas supply and check all fittings and connections for leaks with a soap and water solution.

HOW TO TURN ON

1. Push the “I” on the ON/OFF switch to turn ON. System will take

approximately 7-10 seconds before ignition after the gas line is

purged. See Fig. 33. The main flame ignites (defaults) in the HIGH

position. Press the “I” on the LOW/HIGH button to adjust to the LOW

flame setting, if desired.

2. If fire pit does not light after second try, turn main gas OFF, wait 5

minutes and repeat steps 1.

Note

: A continuous pilot flame can be turned ON or OFF using the continuous pilot switch.

HOW TO TURN OFF

1. To turn OFF the fireplace press the “O” position on the ON/OFF switch. This will turn OFF the fireplace.

NOTE:

Fireplace must turned OFF for 5-minutes before relighting.

LEARN BUTTON: IS ONLY USED WHEN PROGRAMMING REMOTE CONTROLS

REMOTE CONTROL OPERATION

If using a remote control, the rocker switches in the control panel will not be used. Depending on the remote control,

simply press the ON button to operate the fireplace. See bottom of page 24 for reference.

Fig. 33

Control panel

ON/OFF

LOW

HIGH

LEARN

CONT.

PILOT

Содержание Kalea Bay OFP-60LECO-N







































Результаты поиска

Содержание Kalea Bay OFP-60LECO-N

Отзывы:

Похожие инструкции для Kalea Bay OFP-60LECO-N

Бренды по названию

Популярные бренды

Firegear Kalea Bay OFP-60LECO-N, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Kalea Bay OFP-60LECO-N

Отзывы:

Похожие инструкции для Kalea Bay OFP-60LECO-N

Бренды по названию

Популярные бренды