FingerTec Face ID 5 Series Скачать руководство пользователя страница 51

Страница: 51 / 52

“Duplicate Finger” Appears

FingerTec terminals are intelligent. It will not accept the same fingerprint twice

into its system. If you have registered a finger into the terminal, the system would

prompt “duplicate finger” when you try to enroll that finger for another time.

Choose a different finger to proceed.

RFID Card Doesn’t Respond

Two possibilities for this problem

Have you registered the card to the terminal?

The card must be registered to the terminal before it can read the information in

the card. Refer to chapter 3 User for card enrolment.

Have you assigned the user ID to the verification group that supports

RFID card?

Without setting the terminal to show that you are under a group that supports RFID

card, the terminal wouldn’t read your card.

No Sound

A few things could cause this problem:

The terminal voice mode is silent

Perhaps someone has turned off the voice in your terminal or reduced its volume to

0%. Refer to Chapter 6 Personalization.

Speaker is damaged

Once you have rectified the voice mode, if the problem persists, proceed to test

the voice. Go to Chapter 10 to do the test. If no voice is being emitted, contact your

local reseller for support.

For more troubleshooting, go to

http://user.fingertec.com/

Содержание Face ID 5 Series




















































Результаты поиска

Содержание Face ID 5 Series

Отзывы:

Похожие инструкции для Face ID 5 Series

Бренды по названию

Популярные бренды

FingerTec Face ID 5 Series, Руководство пользователя

Результаты поиска

Содержание Face ID 5 Series

Отзывы:

Похожие инструкции для Face ID 5 Series

Бренды по названию

Популярные бренды