Fidelity Electronics 19eA Скачать руководство пользователя

Страница: 54 / 62

ad value of LD1,
weight value of LD2
and ad value of LD2



= weight value of LD1. Data length = 8 including decimal

with leading space (Hex code 20).



= ad value of LD1. Data length = 8 (integers only) with

leading space (Hex code 20).



= weight value of LD2. Data length = 8 including decimal

with leading space (Hex code 20).



= ad value of LD2. Data length = 8 (integers only) with

leading space (Hex code 20).

ad value of zero point
(offset), span weight
value, net span AD
value



= as value of zero point. Data length = 8 (integers only) with

leading space (Hex code 20).



= span weight value. Data length =8 including decimal with

leading space (Hex code 20).



= net span AD value. Data length = Data length = 8 (integers

only) with leading space (Hex code 20)

Weight unit
enable/disable for kg,
g and lb



= kg: - 0 = Off; 1 = On



= g: - 0 = Off; 1 = On



= lb: - 0 = Off; 1 = On

Filter strength

0 = level 1; 1 = level 2; … ;7 = level 8; 8 = level 9

Initial Zero range,
manual zero range,
auto zero tracking
speed



= initial zero range: - 0 = Off, 1 = 1%, 2 = 2%; … 5 = 5%; 6 =

10%; 7 = 20%



= manual zero range: - 0 = 1%; 1 = 2%; 2 = 3%; 3 = 4%; 4 =

5%; 5 = 10%; 6 = 20%; 7 = 50%; 8 = 75%; 9 = 100%



= auto zero tracking speed: - 00 = Off; 01 = 0.25e; 02 =

0.50e; 03 = 10e; 04 = 1.5e; 05 = 2.0e; 06 = 2.5e; 07 = 3.0e; ….;
09 = 5e; 10 = 7.5e; 11 = 10e

Auto tare, repetitive
tare and preset tare



= auto tare: - 0 = Off; 1 = On; 2= Continuous



= repetitive tare: - 0 = Off; 1 = On



= Preset tare: - 0 = Off; 1 = On

Stability control of
manual zero and
manual tare



= manual zero stability control: - 0 = no (disable); 1 = Yes

(enable)



= manual tare stability control: - 0 = no (disable); 1 = Yes

(enable)

Auto power off time,
backlight brightness,
auto power saving,
keypad buzzer and
system buzzer



= auto power off time: - 0 = Off; 1 = 1 minute; 2 = 3 minute; 3

= 5 minute; 4 = 10 minute; 5 = 20 minute



= backlight brightness (01 ~ 04). 01 = lowest, 04 = highest.



= auto power saving: - 00 = Off; 01 = On



= keypad buzzer: - 0 = Off; 1 = On



= system buzzer: - 0 = Off; 1 = On

Check result buzzer,
near zero value, high
limit for weighing, low
limit for weighing,
high limit for
counting, low limit for
counting



= check result buzzer: - 0 = Off; 1 = In; 2 = Out; 3 = hi, 4 = lo



= near zero value. Data length = 8 with leading space (Hex

code 20)



= Hi Limit for weighing. Integer only. Data length = 8

including decimal with leading space (Hex code 20).



= Lo Limit for weighing. Integer only. Data length = 8

including decimal with leading space (Hex code 20).



d5:

= Hi Limit for counting. Integer only. Data length = 8

(integers only) with leading space (Hex code 20).



: = Lo Limit for counting. Integer only. Data length = 8

(integers only) with leading space (Hex code 20).

Comport 1 working
mode, baud rate,
output protocol, print



= working mode: - 0 = Auto 1; 1 = Auto 2; 2 = Auto 3; 3 =

Manual; 4 = PC; 5 = Scanner; 6 = Off

Содержание 19eA































































Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды

Fidelity Electronics 19eA, Руководство по эксплуатации

Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды