Fidelity Electronics 19eA Скачать руководство пользователя

Страница: 17 / 62

F21

Lab 2 Weight Function Output Print

Format

** STD

CUSTOM

F22

Lab 2 Counting Function Output Print

Format

** STD

CUSTOM

F23

Reserved.

F24

Lab 2 Animal Functions Output Print

Format

** STD

CUSTOM

F25

Reserved.

F26

Near Zero

Weight Value

** 000000

Near Zero value is useful for dynamic weight check applications to bypass unnecessary LO alarm during uploading and unloading process. Notes: -



Value entered valid only when Check function is activated.



Near zero weight value can be any value between 20d and LO limit.



Any near zero value which less than 20d will be ignored. Instrument will deem 20d as minimum near zero weight value.



The HI LO comparison remains non-activated when weight reading is less than the near zero value entered here.

F27

Reserved.

F28

Ask for Operator Number when Power on

Yes

** No



Yes: - Instrument will ask for operator number during countdown process when power on. Enter 4-digit operator number or press

[CE/x10]

to skip operator number when being

asked.



No: - Instrument will not ask for operation number.

F29

Read Calibration and parameter set counts.



O (Parameter set count): - shows total times that the important parameters (F80~F88) has been altered.



C (Calibration count): - shows total times of calibration.

F30

Allow Letters and Symbols for Customer

& Product Code Manual Entry

** Off

F31

Auto Power Saving

Off

** On



Off = Auto Power Saving disable.



On = Display brightness will switch to minimum when weight remains unchanged for 30 seconds.

Note:

- Auto Power Saving will be disabled when an energized power adaptor is plugged in.

F32

Optical Key Assignment



** Off (Key disable)



[Zero]



[Tare]



[Print / M+]

Содержание 19eA































































Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды

Fidelity Electronics 19eA, Руководство по эксплуатации

Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды