manualshive.com logo in svg

FIC AN19C, Руководство пользователя, Страница: 42 / 55

Поделиться
Скачать
FIC AN19C Скачать руководство пользователя страница 42

3 - 18

AN19E/AN19C Mainboard Manual

UART Mode Select

This filed allows the users to configure what IR mode the 2nd serial port

should use. The default is Normal.

Options: Normal, IrDA and ASKIR.

RxD, TxD Active

This field configures the receive and transmit signals generated from the IR

port.  The default is Hi Lo (when UART Mode Select is not set to Normal).

Options: Hi Hi, Hi Lo, Lo Hi, and Lo Lo.

IR Transmission delay

This item allows you to enabled/disable IR transmission delay.

Options: Enabled, Disabled.

UR2 Duplex Mode

This item allows you to select IR half/full duplex function.

Options: Half, Full.

Use IR Pins

This item allows you to select IR transmission routes, one is RxD2, TxD2

(COM Port) and the other is IR-Rx2Tx2.

Options:  IR-Rx2Tx2, RxD2, TxD2.

 Super IO Chip Setup

Onboard FDC Controller

Select Enabled if your system has a floppy disk controller (FDC) installed on

the system board and you wish to use it.  If you install and-in FDC or the

system has no floppy drive, select Disabled in this field.

Options: Enabled, Disabled.

Onboard Serial Port 1/2

Select an address and corresponding interrupt for the first and second serial

ports. Options: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.

Содержание AN19C
























































Отзывы:

Нет отзывов