FIC AN19C Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 55

FIC AN19C Скачать руководство пользователя страница 30

3 - 6

AN19E/AN19C Mainboard Manual

First /Second/Third/Other Boot Device

The BIOS attempts to load the operating system from the devices in the

sequence selected in these items.

Options: Floppy, LS120, HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3,

ZIP100, USB-FDD, USB-ZIP, USB-CDROM, USB-HDD, LAN, Disabled.

Boot Other Device

When enabled, the system searches all other possible locations for an

operating system if it fails to find one in the devices specified under the

first, second, and third boot devices. The default is Enabled.

Options: Enabled, Disabled.

Swap Floppy Drive

This will swap your physical drive letters A & B if you are using two floppy

disks. The default is Disabled.

Enabled: Floppy A & B will be swapped under the O/S.

Disabled: Floppy A & B will be not swapped.

Boot Up Floppy Seek

If this item is enabled, it checks the size of the floppy disk drives at start-up

time. You don’t need to enable this item unless you have a legacy diskette

drive with 360K capacity. The default is Disabled.

Options: Enabled, Disabled.

Boot Up NumLock Status

This controls the state of the NumLock key when the system boots. The

default is On.

On: The keypad acts as a 10-key pad.

Off: The keypad acts like cursor keys.

Gate A20 Option

This refers to the way the system addresses memory above 1 MB (extended

memory). The default is Normal.

Normal:

The A20 signal is controlled by the keyboard controller or chipset

hardware.

«
...
28
29
30
31
32
...
»

Содержание AN19C
























































Отзывы:

Нет отзывов