FHP AHP 641-224 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 42

FHP AHP 641-224 Скачать руководство пользователя страница 38

38

The RS-Pro Sensor interface

The RS-Pro sensor factory part number 641-230 is a combination keypad/display unit that
attaches to a control module to let you view and change temperature and set points values and
the controller’s components status, the following features only apply to the software version
covered on this manual.

ICONS

Alarm Bell

Indicates Alarm Condition (see INFO button for more information)

Cooling

Indicates unit enabled in cooling mode

Heating

Indicates unit enabled in heating mode

Occupied

Indicates unit in occupied mode

Unoccupied

Indicates unit in unoccupied mode

Fan

Indicates fan output energized

BUTTONS

ANUAL ON

Places unit into occupied mode. Allows for incremental increase in override
time ( 60min, 120min, 180 min , 4hrs, 5hrs, 6hrs, 0 min) each time button is
pressed

WARMER

Allows for increase in zone temperature setpoint (+1° to per push to a
maximum of +5° or as configured at DDC through BAC view6) from default
setpoint value

COOLER

Allows for decrease in zone temperature setpoint (-1° to per push to a
maximum of -5° or as configured at DDC through BAC view6) from default
setpoint value.

«
...
36
37
38
39
40
...
»

Содержание AHP 641-224











































Отзывы:

Нет отзывов