Festo YXCR страница 3 Скачать руководство пользователя

Страница: 3 / 108

Festo — YXCR — 2021-07b

Table of contents

Applicable documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1

General safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2

Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3

Training of qualified personnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Product overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1

Product design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.2

Modules of the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.2.1

X-module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.2.2

Y-module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2.3

Z-module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3

Delivery status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Transport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1

Transportation protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2

Remove transportation locks from the transportation protection. . . . . . . . . . . . . . . . . . 18

5.3

Transport kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.3.1

Mounting the transport kit (EHMX-EGC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.3.2

Mounting the transport kit (EHMX-ELGC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.3.3

Lifting the product with the transport kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.4

Removing transportation locks from the moving parts. . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.1

Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6.2

Mounting attachments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.3

Preparing mounting surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.3.1

Prepare mounting surface for mounting kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.3.2

Preparing mounting surface for the adjusting kit. . . . . . . . . . . . . . . . . . . . . . . 31

6.3.3

Preparing motor mounting at centre motor position (EHMX-EGC-...-M). . . . . 33

6.4

Using mounting components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

6.4.1

Using mounting kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

6.4.2

Application of adjusting kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

6.5

Product assembly with “partially mounted” delivery status. . . . . . . . . . . . . . . . . . . . . . . 43

6.5.1

Mounting X-module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

6.5.2

Mounting Y-module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

6.5.3

Mounting Z-module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6.6

Mounting connecting shaft at centre of motor position (EHMX-EGC-...-M). . . . . . . . . . . 65

6.7

Mounting connecting shaft at motor position left/right (EHMX-EGC-...-L/-R). . . . . . . . . 73

6.8

Product assembly with delivery status "completely assembled". . . . . . . . . . . . . . . . . . . 80

6.9

Checking structure and alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

6.10 Motor with brake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.11 Attachment component. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Содержание YXCR












































































































Результаты поиска

Содержание YXCR

Отзывы:

Похожие инструкции для YXCR

Бренды по названию

Популярные бренды

Festo YXCR, Руководство по эксплуатации

Результаты поиска

Содержание YXCR

Отзывы:

Похожие инструкции для YXCR

Бренды по названию

Популярные бренды