Festo YXCR Скачать руководство пользователя

Страница: 94 / 108

Festo — YXCR — 2021-07b

Installation

Line/signal

X-module (1)
EHMX-ELGC

Y-module (2)
EHMY-RP-ELGC

Z-module (3)
EHMZ-EGSC

Motor cable (WD)

WD 1.1

WD 2.1

WD 3.1

Encoder cable (WD)

WD 1.2

WD 2.2

WD 3.2

Brake cable (WD)

WD 1.3

WD 2.3

WD 3.3

Sensor signal axis (WG) WG 1.1

WG 2.1

WG 3.1

Sensor signal front
unit/multi-pin plug
(WG)

–

WG 4.1

Tab. 36: System of cable identification (product version with ELGC axes)

Hoses

–

The tubing must be uniquely identifiable.

–

The tubing supplied at the factory is only suitable for the compressed air medium.

–

Only use tubing with material type PUN-H.

Tubing colour

Function

Black

Extend pneumatic drive

Silver

Retract pneumatic drive

Blue

Customer-specific application

Tab. 37: Classification of tubing colours

Tubing size

Bending radius, min-
imum

DHMZ-DGSL-...

PUN-H-3x0.5

12 mm

–

PUN-H-4x0.75

17 mm

–

PUN-H-6x1

26.5 mm

–

Tab. 38: DHMZ-DGSL: tubing size/minimum bending radius (product version with EGC axis)

Tubing size

Bending radius, min-
imum

DHMZ-DGST -...

PUN-H-4x0.75

17 mm

–

PUN-H-6x1

26.5 mm

–

Tab. 39: DHMZ-DGST: tubing size/minimum bending radius (product version with ELGC axis)

7.2.2

Chamber allocation for energy chain

The energy chains are subdivided into chambers by separators.
The chambers are shown schematically from the point of view of the open end of the energy chain.

Содержание YXCR












































































































Результаты поиска

Содержание YXCR

Отзывы:

Похожие инструкции для YXCR

Бренды по названию

Популярные бренды

Festo YXCR, Руководство по эксплуатации

Результаты поиска

Содержание YXCR

Отзывы:

Похожие инструкции для YXCR

Бренды по названию

Популярные бренды