Festo CPX-AP-I-4IOL-M12 Скачать руководство пользователя страница 20

Страница: 20 / 30

IO-Link master event codes

IO-Link
event
code hex

Diagnostics ID
hex

Message

Description

No IO-Link device connected

Remedy

–

Check whether an IO-Link
device is connected.

1800h

01A9

No device connected

Diagnost-
ic status

Error

The recognized IO-Link device does not match
the configured VendorID.

Remedy

–

Check whether the correct IO-
Link device is connected.

1802h

016B

Incorrect VendorID;
deviation of the
Inspection Level

Diagnost-
ic status

Error

The recognized IO-Link device does not match
the configured Device ID.

Remedy

–

Check whether the correct IO-
Link device is connected.

1803h

01A8

Incorrect Device ID;
deviation of the
Inspection Level

Diagnost-
ic status

Error

IO-Link Backup/Restorefailed

–

memory out of

range (2048 octets)

Remedy

–

1809h

0183

BackupInconsistency;
memory out of range
(2048 octets)

Diagnost-
ic status

Error

IO-Link Backup/Restore failed.
DataStorageIndex not available

Remedy

–

180Ah

0184

BackupInconsistency;
DataStorageIndex not
available

Diagnost-
ic status

Error

IO-Link Backup/Restore failed. Unspecific
error in data memory

Remedy

–

180Bh

0185

Backup inconsist-
ency; non-specific
error during data stor-
age

Diagnost-
ic status

Error

Diagnostics and fault clearance

Festo — CPX-AP-I-4IOL-M12 — 2020-03

Содержание CPX-AP-I-4IOL-M12






























Результаты поиска

Содержание CPX-AP-I-4IOL-M12

Отзывы:

Бренды по названию

Популярные бренды

Festo CPX-AP-I-4IOL-M12, Инструкция по эксплуатации

Результаты поиска

Содержание CPX-AP-I-4IOL-M12

Отзывы:

Бренды по названию

Популярные бренды