Festo CPX-AP-I-4IOL-M12 Скачать руководство пользователя страница 14

Страница: 14 / 30

ID hex (dec)

Message

Description

The connected sensor is defective or generates too much
load on its channel.

Remedy

–

Check sensor for correct function, in par-
ticular for current consumption.

–

Check sensor cabling.

010B

(16843019)

Short circuit/overload
in sensor supply

Diagnost-
ic status

Error

Undervoltage of the logic supply PS 24 V DC was detec-
ted.

Remedy

–

Check logic supply PS.

0016

(33619990)

Undervoltage in logic
supply PS 24 V DC

Diagnost-
ic status

Warning
Error

Undervoltage in the load supply PL 24 V DC was detected.

Remedy

–

Check load supply PL.

0105

(33620229)

Undervoltage in load
supply PL 24 V DC

Diagnost-
ic status

Error

A switch-off of the load supply PL was detected. The cause
can be a deliberate shutdown by the emergency stop.

Remedy

–

Check if the emergency stop was activ-
ated.

–

Check load supply PL.

0106

(33620230)

Switch-off load supply
PL 24 V DC

Diagnost-
ic status

Information

Overvoltage load supply PL 24 V DC

Remedy

–

Check load supply PL.

013F

(33620287)

Overvoltage load sup-
ply PL 24 V DC

Diagnost-
ic status

Error

Device undertemperature

Remedy

–

Check ambient conditions.

002D

(50397229)

Undertemperature
Device

Diagnost-
ic status

Error

Output process data watchdog of the AP module expired

0130

(134283568)

Output process data
watchdog of the AP
module expired

Remedy

–

Restart AP system.

–

Check the cable.

Diagnostics and fault clearance

Festo — CPX-AP-I-4IOL-M12 — 2020-03

Содержание CPX-AP-I-4IOL-M12






























Результаты поиска

Содержание CPX-AP-I-4IOL-M12

Отзывы:

Бренды по названию

Популярные бренды

Festo CPX-AP-I-4IOL-M12, Инструкция по эксплуатации

Результаты поиска

Содержание CPX-AP-I-4IOL-M12

Отзывы:

Бренды по названию

Популярные бренды