Festo 548076 страница 85 Скачать руководство пользователя | Manualshive

Страница: 85 / 92

background image

85 / 92

Festo 7DHTGd_en

7. Insert ball bearings into the housing.

Note

The number of ball bearings depends on the size of the rotary indexing table

(see Table).

Type

Number of ball bearings

DHTG-65-…-A

1

DHTG-90-…-A

2

DHTG-140-…-A

2 or 3

DHTG-220-…-A

2 or 3

Ensure that the top rail of the ball bearings is not pressed down into the
housing. The balls of the ball bearings must run between the rails, otherwise
the plate may not be able to move and the balls of the ball bearings and the
rails could be irreparably damaged.

Note

When screwing in the clamping ring the plate seal can be pulled into the
joint between the plate and housing.
In this case, pull the plate seal out of the joint before screwing in the clamp-

ing ring any further. To this end, guide a flat, blunt object next to the pulled

in area under the seal and use it to move along the seal until the sealing lip
completely lies on the housing.

8.

Tighten the clamping ring using two pin punches and a hole profile (or

another suitable lever tool).

To tighten the clamping ring, the rotary indexing table must be held in place

(if necessary, with the help of a second person or by fixing the rotary index

-

ing table).

The correct preload of the guide segments is reached when the index hole

(arrow) is level with the screw hole and the clamping ring is flush with the

plate surface.

For design reasons, there are two screw holes in sizes DHTG-65 and DHTG-90.

The correct pretension is achieved with the hole marked during removal.

9.

Screw the flat head screw into the plate and tighten to the appropriate tight

-

ening torque (see table).

Type

Torque

DHTG-65-…-A

0.6 Nm

DHTG-90-…-A

0.6 Nm

DHTG-140-…-A

0.6 Nm

DHTG-220-…-A

0.6 Nm

«
...
83
84
85
86
87
...
»

Содержание 548076





























































































Отзывы:

Нет отзывов

Похожие инструкции для 548076

Бренд: Raymarine Страницы: 70

Бренд: Landoll Страницы: 83

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: CAMAG Страницы: 40

FreeStyle Comfort

Бренд: CAIRE Страницы: 33

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: Panta Safe Light Страницы: 2

Бренд: Calrec Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды