Festo 548076 Скачать руководство пользователя

Страница: 62 / 92

62 / 92

Festo 7DHTGd_en

8. Lever the O-ring out of the inside of the hole in the plate.

9. Lever the two rails of the guide segments out of the housing.

If only plate components have to be repaired, you can continue with the assembly in

Chapter 4.5.5 on page 81

4.4.4

Dismantling the plate (DHTG-220)

1. Release the pretension of the screw. To do this, use a pin punch and a ham-

mer to tap the screw head.

2. Undo the countersunk screws in the index plate and unscrew uniformly.

Note

The ring gear is equipped with overload protection. It is subjected to spring
tension and can tilt when the countersunk screws are unscrewed on one
side.

3. To undo the index plate, screw three countersunk screws uniformly into the

threaded holes of the index plate.

Содержание 548076





























































































Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды

Festo 548076, Инструкции по ремонту

Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды