7
TYPE
PR 419
PART NUMBERS
022-4504-000 (120V, 60Hz) USA,
022-4534-000 (240V, 50Hz) Aust,
022-4544-000 ( 230V, 60Hz) UK,
022-4564-000 (230V,50Hz) Eur,
022-4574-000 (100V, 50/60Hz) Japan
POWER REQUIREMENTS
540W
POWER AMPLIFIER
OUTPUT:
200W RMS into 4
Ω
@ <1%THD
SENSITIVITY:
1V RMS
PRE AMPLIFIER
INPUT IMPEDANCE:
PASSIVE: 1M
Ω
,
ACTIVE: 1M
Ω
SENSITIVITY FOR FULL POWER:
PASSIVE: 20mV,
ACTIVE: 40mV
NOMINAL LEVEL:
PASSIVE: 150mV,
ACTIVE: 300mV
TONE CONTROLS
BASS: ±15dB @ 50Hz
SEMI-PARAMETRIC CONTROL:
MID FREQUENCY: 150 to 1500Hz
MID LEVEL: ±15dB @ MID FREQUENCY setting
TREBLE: ±15dB @ 5kHz
ROOM BALANCE:
± 10dB, crossover frequency: 350Hz
EFFECTS LOOP
SEND IMPEDANCE:
1k
Ω
RETURN IMPEDANCE:
22k
Ω
NOMINAL LEVEL:
+4dBu
SPEAKERS
LOW FREQUENCY:
Fender Special Design 4
Ω
, 15” Woofer (P/N 0048941000)
HIGH FREQUENCY:
Foster Compression Driver (P/N 0048847000)
DIMENSIONS
HEIGHT:
25.5 in.
(65 cm)
WIDTH:
23 in.
(59 cm)
DEPTH:
13 in.
(33 cm)
WEIGHT
65 lb.
(30 kg)
Product specifications are subject to change without notice.
A. IEC LINE CORD CONNECTOR
- The power line cord
must
be connected to a grounded AC receptacle in accordance
with the voltage and frequency ratings as labeled on the
Rear Panel under INPUT POWER.
B. GROUND LIFT
- Switch IN disconnects the ground circuit
from the LINE OUT jack {C} (pin-1) which may reduce
noise or hum. Switch OUT is usually the best setting.
C. LINE OUT
- Balanced XLR jack for output to recording or
sound-reinforcement equipment.
D. LINE OUT LEVEL
- Adjusts the output level of LINE OUTjack {C}.
E. PRE/POST EQUALIZATION
- Switch IN supplies the LINE
OUT jack {C} with the post-equalization (EQ modified) signal
from the amplifier. Switch OUT supplies the LINE OUT jack
{C} with the pre-equalization (EQ unmodified) signal.
F. TUNER
- Connect your instrument tuner at this output jack.
This is the only output NOT disabled by the MUTE switch
allowing for quick, silent tuning of your bass while plugged
into the Bassman 200.
G. EFFECTS RETURN
- Connect the cable from
the output of your external effects device to
this input jack.
H.
EFFECTS SEND
- Connect cable from this
output jack to the input of your external effects
device.
•
LINKING TWO BASSMAN 200
AMPLIFIERS:
For additional output, link two Bassman
200’s together by connecting the EFFECTS SEND jack {H}
from the “primary” amp to the EFFECTS RETURN jack {G}
of the “secondary” amp. All settings on the primary amp will
control the secondary amp settings
except
MASTER
VOLUME which must be set on each Bassman 200 .
Ground
Lift
Line
Out
Pre/Post
EQ
Tuner
Gnd
Lift
Pre
Post
Line
Out
Level
Return
Send
TYPE: PR 419
540W
SERIAL NUMBER
MADE IN MEXICO
C
D
E
F
G
H
A
B
S
Sp
pe
ec
ciif
fiic
ca
at
tiio
on
ns
s
S
Sp
pe
ec
ciif
fiic
ca
at
tiio
on
ns
s
B
B
B
B
a
a
a
a
s
s
s
s
s
s
s
s
m
m
m
m
a
a
a
a
n
n
n
n
2
2
2
2
0
0
0
0
0
0
0
0
-
R
Re
ea
ar
r P
Pa
an
ne
ell
R
Re
ea
ar
r P
Pa
an
ne
ell
ENGLISH
ENGLISH
ESP
AÑOL
ESP
AÑOL
FRAN
ç
AIS
FRAN
ç
AIS
IT
ALIANO
IT
ALIANO
DEUTSCH
DEUTSCH
I. HORN LEVEL
- Adjusts the
volume level of the horn.
The horn is OFF with the
knob turned counter-
clockwise to “Min.”
J. FUSE
- Protects the horn
from overdrive or electrical
fault damage. Replace fuse with same type and rating
(2A, 250V).
