EN
8
1.5
STANDARD SAFETY PROCEDURS
- Do not use the machine in very damp places or in the
presence of infl ammable liquids or gases.
- Do not use it in the open air when general weather and
environmental conditions are unfavourable (eg. explosive
atmospheres, during a storm or rain).
- Wear suitable clothes, without wide sleeves or articles such
as scarves, chains and bracelets which could get caught
in the moving parts.
- Always use personal protection devices: protective goggles
as recommended by safety standards, gloves of the right
size, headphones or earplugs, and hairnets if necessary.
- Use the tools recommended in this manual if you want
to achieve the best performance from your sawing
machine.
- Any power cable extensions must be type approved and
comply with safety standards.
- Avoid using the machine if your psycho-physical condition
are precarious or upset.
1.6
SAFETY PROCEDURS FOR FURTHER RISK
- Always keep processing residues away from the cutting
area.
- Always use the clamp. The parts to be cut must always be
held fi rmly in the clamp.
- Always keep hands away from the working areas while the
machine is moving: before loading or unloading the part,
release the run button on the hand grip.
- Do not force the machine unnecessarily : excessive
cutting pressure could cause rapid wear to the blade and
negatively infl uence the performance of the machine in
terms of fi nishes and cutting precision.
1.7
INFORMATION REGARDING NOISE AND
VIBRATIONS
In normal conditions of use as described in this manual,
this belt sawing machine determines an equivalent level of
acoustic pressure:
Leq = 79,0 dB (A) when operating unloaded
Leq = 81,2 dB (A) during processing (eg. cutting of a steel
tube D. 130 mm thickness 10 mm), at cutting speed of 70 mt/
min. with a weighted operating cycle of 2 minutes.
The frequency root mean RMS weighed for hand-arm
acceleration does not exceed 2.5m/s².
The measurements are taken in accordance with
standards UNI7712, ISO3740, ISO 3746 and EC/2006/42
The emission levels indicated are not necessarily safety
levels. Although there is a relationship between the emissions
and exposure levels, the values shown cannot be used for
establishing the need for further precautions. There are other
factors which infl uence the exposure levels of operators, such
as the features of the work place, presence of other sources
of noise, number of machines running, etc.
The exposure levels may also vary between countries.
This information is necessary for the user for better evaluation
of the risks and hazards deriving from noise.
NOTE: Personal hearing protention should be
used, such as headphones or earplugs.
1.8 INFORMATION
ABOUT
THE
ELECTROMAGNETIC COMPATIBILITY
The European regulations on safety and, in particular, the
Directive
EC/2004/108
contemplate that all the equipment be
equipped with shielding devices against radio interferences
both from and towards the outside.
This machine is equipped with fi lters through which the
machine is safe and in compliance with above regulations.
Tests were carried out according to 61000-6-1, EN 61000-
6-3, EN 55014-1, EN 55014-2 regulations.
1.9
DESCRIPTION OF THE MACHINE (Fig. 1)
The belt sawing machine consists of two basic parts: the
machine body
5
complete with motor and drive
7
which is
integrated into lower part, consisting of the clamp
11
, the
base
13
and swivel support
9
.
Here is a list of the main parts with the number indicating it
in the drawing.
Legend
Fig. 1
1
Grip
2
Blade tension handwheel
3
Handle for handling
4
Sliding blade guide
5
Machine
body
6
Blade
7
Motor
8
Control
box
9
Bar
stop
10
Clamp (vice)
11
Morsa
12
Clamp drive
13
Base
WEIGHT ...................................................................
38 Kg.
SIZE .................................
cm 108 x 75 x H80 in maximum
..............................................................overall dimensions.
PACKAGING SIZE
.............................. cm 100 x 39 x H57
2 INSTALLATION
2.1
REMOVING THE PACKING
Remove the wooden frame which protects the machine
during transit.
Try not to damage the frame as you may have to move the
machine long distances or store it for long periods.
2.2
HANDLING (Fig. 2)
As the machine is considerably heavy (38 kg net), it needs
at least 2 people to lift it, positioned on either side.
The machine must be lifted and transported by the handle
3
fi xed on the base plate.
