Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 55

Страница: 55 / 110

6.2 Starting the engine

Exhaust fumes contain toxic substances and can damage your

health, cause unconsciousness or even death.

WARNING!
Danger of poisoning by exhaust gases!

–

Do not inhale exhaust gases.

–

Avoid operation in closed or partly closed

rooms, or ensure adequate ventilation when

working in trenches.

Components can be very hot during or immediately after operation.

WARNING!
Danger of burning on hot components!

–

Wear your personal protective equipment (pro-

tective gloves, protective clothing).

–

Avoid touching hot components.

WARNING!
Loss of hearing caused by too high noise bur-

dens!

–

Wear your personal protective equipment (ear

protection).

Operate the machine only with the guide handle mounted and low-

ered.

Protective equipment:

Hearing protection

Working clothes

Protective gloves

Safety shoes

The engine does not start if the oil level is too low.

Fold down the guide handle into working position.

Make sure that nobody is in the danger zone.

Operation – Starting the engine

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды