Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 59

Страница: 59 / 110

6.3 Operation

Guide the machine only by the guide handle.

Guide the machine so that your hands do not hit against solid

objects.

Keep feet clear of the vibrating base plate.

CAUTION!
Danger of injury caused by uncontrolled

machine movement!

–

Always hold on to a running machine.

–

Always keep an eye on a running machine.

Components can be very hot during or immediately after operation.

WARNING!
Danger of burning on hot components!

–

Wear your personal protective equipment (pro-

tective gloves, protective clothing).

–

Avoid touching hot components.

WARNING!
Loss of hearing caused by too high noise bur-

dens!

–

Wear your personal protective equipment (ear

protection).

Protective equipment:

Hearing protection

Working clothes

Protective gloves

Safety shoes

Make sure that no persons are in the danger zone.

NOTICE!
The centrifugal clutch may be damaged!

–

Operate the machine only with the

throttle lever in “MAX” position.

Set the throttle lever to “MAX” position.

Machine vibrates forward.

Fig. 45

Operation – Operation

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Бренды по названию

Популярные бренды