Fayat DYNAPAC DFP8 Скачать руководство пользователя страница 76

Страница: 76 / 110

8.6 Weekly

8.6.1 Checking, cleaning the air filter

NOTICE!
Danger of engine damage!

–

Do not start the engine after having removed

the air filter.

–

If necessary, the air filter may be cleaned up to

six times.

–

Cleaning does not make sense if the air filter

element is covered with a sooty deposit.

–

Do not use gasoline or hot fluids to clean the

filter element.

–

After cleaning, the air filter must be inspected

for damage using a torch.

–

Do not continue to use a damaged air filter ele-

ment. If in doubt use a new air filter.

Protective equipment:

Working clothes

Safety shoes

Protective gloves

Safety goggles

Park the machine safely

Chapter 6.5 ‘Parking the machine

in secured condition’ on page 62

Allow the engine to cool down.

Unscrew wing nut (1) and remove cover (2).

Clean the cover.

Unscrew wing nut (3) and remove filter element (4).

Check the rubber seal (5), replace if necessary.

The rubber seal frequently sticks to the filter

element.

B-SYM-1074

Fig. 58

Disassembling the air filter

B-HON-0033

Fig. 59

Maintenance – Weekly

DFP8

Содержание DYNAPAC DFP8















































































































Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды

Fayat DYNAPAC DFP8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DYNAPAC DFP8

Отзывы:

Похожие инструкции для DYNAPAC DFP8

Бренды по названию

Популярные бренды