FarragTech CARD G Скачать руководство пользователя страница 84

Страница: 84 / 101

FAULTS AND REMEDY

CARD G / FIT

V 6.15 E / April 2010

18.2

AULTS WITHOUT

ISPLAY

EXT

FIT-display remains dark after switching on the main power switch.



No external power supply.



Check the main power supply to the unit.



External fuses too small or external shortage.



Check for short circuit and fuse sizes.



The LED on 24V DC power supply unit [1G12] is
off.



Short circuit on the 24V DC side of the power
supply unit; disconnect wires from 24V DC
connectors; if LED shines again, follow wires

and remedy short circuit.



Check 220...230V AC supply to the power

supply unit; restore supply – if necessary



No 24V DC power even when the wires on the
24V DC side of the power supply unit [1G12] are
disconnected and 220...230V AC supply is

available.



Replace the power supply unit.

Содержание CARD G






































































































Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды

FarragTech CARD G, Руководство по эксплуатации

Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды