FarragTech CARD G Скачать руководство пользователя страница 78

Страница: 78 / 101

FAULTS AND REMEDY

CARD G / FIT

V 6.15 E / April 2010

The FIT-controller shut down the process heater preemptively to avoid excess temperature in the

heater.



Solenoid valve (1.2) [3Y14] does not open when
drying is activated and pressure switch (1.3)
[2S5] is defective.



24V DC must be measurable at both
terminals (to ground) of the switch when
compressed air is available. Replace the

switch if needed



Check voltage supply 24VDC to valve; if OK,

replace valve.



Compressed air is missing and pressure switch
(1.3) [2S5] is defective.



Restore compressed air supply and replace
pressure switch.



Solid state relay [1V7] is defective.



There must be 220V...230V AC between L-
and N-(L2)wire of the heater when the solid
state relay is powered (green LED is ON)



not, replace SSR.



Heater (1.7) [1E7] defective.



Check heater resistance (290Ohm); if
necessary, replace heater.

This fault cannot be eliminated before

is pressed to switch off the drying process.

The safety thermostat of the process air heater (1.9) [3S8] has tripped.



Solenoid valve (1.2) [3Y14] does not open when
drying is activated and pressure switch (1.3)

[2S5] is defective.



24V DC must be measurable at both
terminals of the switch when compressed air

is available. Replace the switch if needed



Check voltage supply 24VDC to valve; if OK,

replace valve.



Compressed air is missing and pressure switch
(1.3) [2S5] is defective.



Restore compressed air supply and replace
pressure switch.



Solid state relay [1V7] is shorted.



There must not be 220V...230V AC between L-
and N-(L2)wire of the heater when the solid
state relay is not powered (green LED is

dark)



replace SSR if necessary.



Heater (1.7) [1E7] defective.



Check heater resistance (290Ohm); if
necessary, replace heater.

This fault cannot be eliminated before

is pressed to switch off the drying process.

Содержание CARD G






































































































Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды

FarragTech CARD G, Руководство по эксплуатации

Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды